Please choose your bike
Indicator original Triumph connector
CB10742
/ RS-100
€9.95*
The matching flasher in the set (4 pieces for a pair of turn signals) in order not to cut the original wiring harness. These plugs are crimped onto the cables of the turn signals and can then be easily and quickly inserted on the cable harness side.
ABM Wunderkind Levers
CB11029M
/ RS-10
€139.00*
ABM Wunderkind Brake & clutch lever for all triumphs for the best grip. The handle area was much more powerful than any other lever on the market. This results in a very good feeling as it was not known before. We really do not promise too much, because that just feels great. The levers are deep black anodised. The 6-position adjuster is optionally available silver or black, and can be adjusted with one hand even during the journey. With ABE. Another tip from us: Brake and clutch levers are among the popular crashing parts. Therefore it makes sense to always have a pair of spare levers on the tour in the luggage. So just swap in the original in the tankbag.
Tune Map on the original ECU
CB10704
/ RS-10
€299.00*
Your Triumph needs this! Actually an absolute must for every motorcycle. For relatively "little" money, you get a very noticeable improvement in engine running and a clearly noticeable increase in performance.By installing a Classicbike Raisch Map (which we have tested in countless tests and many hours on a DynoJet test bench), the performance of your engine is increased and the engine also runs smoother and healthier.
Motorcycles are simply badly tuned ex works in some engine speed ranges (usually too lean). This reduces the power output and the engine does not run perfectly.
What can you expect from ECU tuning?
A smoother running engine: If you know your Triumph 2 cylinder, you know the problems with the strong load changes and the constant jerking. Throttle application and release are very abrupt transitions. Constant jerking on slow city rides (you ride through the city at 50 km/h in 4th gear and the bike constantly jerks slightly. These problems are significantly improved by the ECU tuning and the motorcycle becomes more pleasant to ride. You can't get rid of it 100%.
More power: The motorcycle gains power and torque across the entire rev range.Depending on the standard dispersion of the engine, this is approx. 8 - 10%.
A suitable mapping for your engine setting:- Most Triumph Modern Classic riders have already tuned something on their bike (an open air intake / exhaust or more).If you do this, you should also adjust your mapping. We have various maps with different exhaust systems etc. & guaranteed to have the right mapping for your machine in between.
Classicbike-Raisch tips:- If you have not yet done anything to your bike and would like a little more power, we recommend other small changes to the bike that will give you noticeably more power for an affordable price.Open air filter cover + Schnuffi (see accessories in this product description) K&N sports air filter (see accessories in this product description) Open exhaust system (see exhaust category) Removal of the restiktor Paltte from the airbox (free of charge, the instructions are available on request from us for ECU tuning)- If you want even more power, you need to delve deeper into the subject matter and engine tuning. You can find more information on this under the heading Tuning.
How does ECU tuning work?
It's very simple! - You order the item here in our store (other items can also be ordered if required)- You remove your ECU (it is clamped in the battery box, the removal takes about 5 minutes).- You pack the ECU together with your order confirmation in a box and send it well packed and insured to our address. Enclose information about what has been changed on your motorcycle/engine.- We will re-record your ECU within 1 - 4 working days (usually we can do it in 1 - 2 days).
Vintage leather Backpack / Sidebag
CB11855M
/ RS-8
€239.95*
A very high quality, handmade genuine leather backpack, which can be used on many motorcycles as a very practical and quickly removable side bag.The backpacks are made of very durable leather, which gets its patina over time and becomes more and more beautiful. A bag to inherit!
The scope of delivery includes fabric straps of different lengths with which the backpack can be attached to many motorcycles within seconds.See assembly video at the end of the description. See below for model specific information.
The practical, rollable closure allows you to vary the size of the bag.Dimensions with rolled up closure: 46 x 25 x 13 cm / 14-15LInside the backpack is a laptop compartment, as well as a small pocket to store small items such as keys.The Vintag leather backpack is also available as a mini version to wear around the neck. You can also attach it to the outside of the backpack with an accessory strap (see accessory items in this description).
Mounting on air-cooled Triumph models: The backpack can be easily mounted to the rear frame with the fabric loops. We recommend to order our panniers with spacers to prevent the bag from dragging on the tyre. (see accessories in the description)
Mounting on water-cooled Triumph models:
Bonneville & Street Twin models: The backpack can be easily mounted to the rear frame with the fabric loops. However, as a precaution we recommend ordering our pannier spacers to prevent the bag from dragging on the tyre. (see accessories in the description)
Scrambler 1200:The backpack can be easily mounted to the rear frame on the left side with the fabric loops.
Thruxton & Speed Twin:The backpack can be easily mounted to the rear frame with the fabric loops. However, as a precaution we recommend ordering our pannier spacers to prevent the bag from dragging on the tyre. (see accessories in the description)
Bobber & Spedmaster:Mounting on the bike with the loops is not easy.
Mounting on BMW R nine T models:Mounting on the motorcycle with the loops not possible without further ado.
CAYO - moto.dokk
CB12691
/ RS-5
€139.90*
The new Cayo cell phone holder system from Motogadget made in Germany.In our opinion, the Cayo system is the best, most sophisticated and easiest to use cell phone holder & charging system available on the market. In contrast to most other manufacturers, you don't have to choose between numerous adapters / accessories etc. With the moto.dokk comes a perfect handlebar mount that integrates everything you really need.
Handlebar mount / inductive charging / anti-vibration system
- The system comes with various adapter rings that allow the mount to be fitted to any handlebar. - A cable for connection to a USB-A socket is included (most modern motorcycles have such a socket). This allows the cell phone to be charged inductively via the holder. If you do not have a USB-A socket, you can order the "battery.dokk" to charge your cell phone via the holder (see accessories in this description).- An anti-vibration plate (to prevent damage to the cell phone / camera) and an inductive charging function are integrated in the holder.
1-click holder / cell phone case
We have tested the holder ourselves on some of our motorcycles and it works perfectly! The cell phone sits firmly in place with a flick of the wrist (no annoying turning / getting stuck or similar). The cell phone can be mounted in either portrait or landscape format.
You have 2 options for attaching the cell phone to the holder:1. you order the stylish and very flat Cayo cell phone case "phone.dokk" (see accessories in this product description).2. you order the "uni.dokk" adhesive pad, which can be universally attached to any cell phone (see accessories in this product description).
Classicbike-Raisch tip
For very good and motorcycle-friendly navigation, we recommend the Calimoto app.
Summary:
The full-featured mounting system. Attaches your smartphone quickly and securely to any motorcycle. Choose a suitable case or universal pad. Direct connection to the vehicle battery is possible with our battery.dokk.
Integrated vibration decoupling Integrated inductive charging smartphone docking in portrait & landscape formatSuitable for all handlebar diametersOur moto.dokk is a mounting system for quickly and securely attaching your smartphone to your vehicle. The extremely compact housing integrates inconspicuously into the vehicle and combines inductive charging and vibration decoupling.
- The scope of delivery includes a connection cable for a USB-A socket on the vehicle. When using an existing USB port on the vehicle, this must be switched on and off with the ignition. Proper functioning of inductive charging is guaranteed with our CAYO phone.dokk cases, provided the phone supports inductive charging. - When using a CAYO uni.dokk pad, inductive charging may be limited or not possible. - If there is no USB port on the vehicle, we recommend our CAYO battery.dokk for direct connection of the moto.dokk to the 12V vehicle battery.
Suitable for all standard handlebar diameters and Fatbars:- 22.2mm (7/8")- 25.4mm (1")- 28.6mm (1 1/8")- 31.8mm (1 1/4")- 35.0mm (1 3/8")
Rambler Backpack / Sidebag
CB12415M
/ RS-5
€229.95*
A very high quality, handmade backpacks made of genuine leather and canvas fabric, which is also very practical to use on many motorcycles as a very quickly removable side bag.The leather straps can be easily stowed at the back of the backpack when hanging it on the motorcycle.For the production of the backpacks are used materials of very high quality, which ensure a very long life despite heavy use on the motorcycle. Genuine leather is used on the one hand and 14 ounce heavy canvas / canvas on the other. The canvas fabric is coated with wax on both sides. The coating is used for water repellent protection. For really heavy rain, a waterproof rain cover is included in the package.
The Rambler backpacks have a padding incorporated in the back area, which provides on the one hand for a higher wearing comfort and makes the backpack stiffer on the other hand, which provides for an easier / better mounting option on the motorcycle.
Included are different lengths of fabric tabs, with which the backpack can be attached to many motorcycles within seconds.See mounting video at the end of the description. Model specific info see below.
Dimensions: 45 x 31 x 15 cm /. Capacity: 24 lInside the backpack are 4 convenient, quick access compartments.
Fits air-cooled Triumph models: The backpack can be easily mounted on the rear frame with the fabric loops. However, as a precaution, we recommend ordering our pannier spacers to prevent the bag from rubbing against the tire. (see accessories in the description)
Fitting to water cooled Triumph models:
Bonneville & Street Twin models: The backpack can be easily mounted to the rear frame using the fabric loops. However, we recommend as a precaution to order our pannier spacers to prevent the bag from dragging on the tire. (see accessory article in the description)
Scrambler 1200:The backpack can be easily mounted to the rear frame on the left side using the fabric loops.
Thruxton & Speed Twin:The backpack can be easily mounted to the rear frame with the fabric loops. However, as a precaution, we recommend ordering our pannier spacers to prevent the bag from rubbing against the tire. (see accessory article in the description)
Bobber & Speedmaster:Mounting on the motorcycle with the loops not easily possible.
Mounting on BMW R nine T models:Mounting on motorcycle with the loops not readily available.
CAYO - bike.dokk
CB12692
/ RS-4
€29.90*
The new Cayo cell phone holder system from Motogadget, made in Germany.In our opinion, the Cayo system is the best, most sophisticated and easiest to use cell phone holder system on the market.
The simple / inexpensive mount for short tours
- The bike.dokk mount is a simple cell phone holder with which you can attach your cell phone to the handlebars of your motorcycle. Various adapter rings are included in the scope of delivery, which enable mounting on all common motorcycle/bicycle handlebars.- We recommend this mount to all customers who only need the mount occasionally for short trips. We recommend the "moto.dokk", which is equipped with a charging function and an anti-vibration system to protect the cell phone camera, for those who regularly have their cell phone on the motorcycle for longer periods of time.
1-Click holder / cell phone case
We have tested the holder ourselves on some of our motorcycles and it works perfectly! The cell phone sits firmly in place with just one click (no annoying turning / getting stuck or similar). The cell phone can be mounted in either portrait or landscape format.
You have 2 options for attaching the cell phone to the holder:1. you order the stylish and very flat Cayo phone case "phone.dokk" (see accessories in this product description).2. you order the "uni.dokk" adhesive pad, which can be universally attached to any cell phone (see accessories in this product description).
Classicbike-Raisch tip
For very good and motorcycle-friendly navigation, we recommend the Calimoto app.
Summary
The quick and secure mounting system for your smartphone. Suitable for bicycles and motorcycles. Select suitable cover or universal pad separately.
Very small & compact on the handlebarsQuick & secure attachmentPortrait & landscape format without conversionSuitable for all common handlebar diameters and Fatbars:
- 22.2mm (7/8")- 25.4mm (1")- 28.6mm (1 1/8")- 31.8mm (1 1/4")- 35.0mm (1 3/8")
CAYO - phone.dokk
CB12693M
/ RS-3
€29.90*
With the Cayo phone.dokk, the cell phone can be attached to all Cayo holders with a flick of the wrist.
The case has an elegant and very flat design to not only be practical but also look good. The surface of the case consists of a very pleasant soft-touch surface.
As a small but not unimportant side effect, the case also protects your cell phone from damage if it falls out of your hand.
An extra strong magnet is integrated into the case, allowing you to attach your phone to all magnetic mounts.
CAYO - uni.dokk
CB12694
/ RS-2
€14.90*
With the Cayo uni.dokk, you can attach your cell phone to all Cayo holders in one easy step.
Don't fancy an extra cell phone case? Or do you already have one that you want to keep using? No problem! The uni.dokk is a strong adhesive pad that sticks to all surfaces.
Chain Set Black Scale - AC
CB12313.1M
/ RS-2
€129.95*
Attention! When ordering in the comments please specify for what a motorcycle and what year of manufacture the set should be. Only for models up to 2014 from 2015 other chains were installed (for this please contact us personally).
RK Black Scale 525 chain set. Perhaps the most elegant chain on the motorcycle market to buy. Black link plates and gold rivets and rollers from the premium manufacturer RK Chaines.The chain kit comes with a rivet lock.
The kit also includes a chainring (choice of a black steel chainring or a stealth chainring in gold / black) and a chain sprocket.A bit further down in the description, you have to pack your desired gears to the set.
We recommend you to choose a shorter gear ratio than the original one from Triumph (this is simply much too long for the engine power). We advise a 18 / 45 or even 17 / 45 gear ratio.
Factory gear ratio:790cc engines: 17 / 43865cc engines: 18 / 43
Tip:- We recommend for safety a new sprocket lock plate with the chain set to order (see accessories article in this description).- In addition, you will find in the accessories still beautiful, black chainring nuts for all who want to have it completely black.
About the RK chain:
For more than 40 years, RK supplies all well-known Japanese motorcycle manufacturers in the original equipment.Also in racing, RK is the first choice of many teams in MotoGP, motocross or even the Paris-Dakar Rally.
The Black Scale is an improved form of the O-ring chains. Due to the special shape of the X-rings, the chain is sealed at four sealing points, the lubricant can not escape.In addition, the X-ring serves as an additional lubricant reservoir. The service life of the chain is extended by about 30%.
Motoscope Chrono Classic 2 Speedo
CB12780
/ RS-1
€519.00*
With us you get everything you need to install and connect the Motogadget Chronoclassic 2 speedometer on your Triumph Modern Classic motorcycle.Model-specific descriptions and necessary accessories can be found below in the description.
The Chronoclassic 2 speedometer is a further development of the German motorcycle accessory manufacturer Motogadget, into which more than 20 years of experience have flowed.Classically elegant design combined with very high-quality materials and absolute high-end workmanship.The elegant Chronoclassic 2 speedometer is probably the highest quality motorcycle speedometer available on the market. The speedometer has a completely metal housing and is manufactured entirely by Motogadget in Germany.The classic round design (80mm diameter) combined with the flat housing (20mm depth) give the speedometer the perfect overall look and allow you to integrate it perfectly into your custom bike.
When switched off, a closed, black dial provides the perfect look: modern, minimalist and at the same time timelessly classic. The digital display, developed by motogadget, consists of a matrix of 512 tiny, super-bright red LEDs that shine through the dial.
Perfectly readable in direct sunlight, the display contains two lines. The top line displays gear and speed, and the bottom line displays values that can be changed at the push of a button. The illuminated pointer, a perfectly illuminated backlight and the automatic brightness adjustment of the matrix LEDs ensure optimal readability even in dark environments.The 11 control lights and the LED display are invisible when switched off.
Model-specific descriptions:
Triumph AC - air-cooled models up to 2015
For all models that have a speedometer with an LCD display (kilometer counter) ex-works, an additional breakout box and breakout box A are required for connection. You can find both of these boxes among the accessories in this description.
If your Triumph has a factory-fitted speedometer cable, we offer the spacer (this allows you to remove the speedometer cable). See accessories in this description.
Among the accessories, you will find a universal mounting bracket to mount the speedometer.
If the speedometer is not recessed in a lamp, we recommend ordering the outer cup as well.
Triumph LC - water-cooled models from 2016
To mount the Chronoclassic 2 speedometer on one of the water-cooled Triumph Modern Classic models, it is essential to additionally install the Additional Tacho Box LC and the Breakout Box A.You can find these under the accessory items in this description.
Among the accessories, you will find a universal mounting bracket to mount the speedometer.
If the speedometer is not recessed in a lamp, we recommend ordering the outer cup as well.
MUD leather side bag system
CB12598M
/ RS-1
€530.00*
Genuine craftsmanship from Italy! The MUD leather bag system is the perfect combination of functionality, old school leather bag look & absolute high end quality / workmanship. The bags are handmade in Italy from very thick leather. A nice soft leather is used to get the casual hanging backpack look and to allow the height variable roll up closure.
Fastening system:The best thing about these bags is that they not only look good, but they also have a very good & practical fastening system.The bags have the SYS quick fastening system on the back. Thanks to this system, the bags can be attached to and removed from the motorcycle with a flick of the wrist and a click.In addition to the bags, a motorcycle model-specific SW-Motech Legend Gear SLC luggage holder is required (you can find this under accessories in this product description). Tip: If you already have a Legend Gear luggage system fitted to your motorcycle, you can simply replace your SW Motech bag with the MUD Bag.
Waterproof: The leather of the bags is properly oiled at the factory, making the bags water-repellent. In other words, if you get caught in a rain shower, the bags will easily remain waterproof. If you get caught in a really heavy downpour on a motorcycle tour, a waterproof rain cover is also included.
Additional belt pouch:There is another small pocket on the front of the bag, this can also be removed if necessary and used as a belt pouch (very practical for storing expensive valuables, for example, that you don't want to leave on your motorcycle when visiting your favorite pub).
Magnetic fasteners:Retro look paired with state-of-the-art magnetic fasteners! The Mud Bag uses classic leather straps with belt buckles as fasteners. However, because such fasteners are not exactly practical, a modern magnetic fastening system is hidden under the belt buckles. The system can be opened and closed in a single movement.The belt buckle therefore only serves as a fixed length adjustment for the leather strap.
Roll up closure / variable size: To close the mud bag, it is rolled up at the top like a classic messenger bag. This looks cool and allows you to make the bag bigger and smaller if necessary. Thanks to the roll-up closure, the bag has a height of 35 to 45 cm.
Extra strap: The bags are available with or without extra leather straps on the sides of the bag. With the bag with the extra straps you can attach things to the left and right of the bag, such as a water bottle, a camera tripod or other things.
Inner lining:A bright orange fabric was carefully chosen as the inner lining to make it easy to find your things in the bag. The contrasting and bright color really makes it much easier to find individual items. The inner lining is also washable.
Size / Volume: Height: 35 - 45 cm Width: 33cmDepth: 17cmVolume: 20 - 25 liters
Triumph 3D lettering - New Generation
CB12589
/ RS-1
€29.95*
Triumph 3D sticker / lettering in New Generation design by Classicbike-Raisch.
The lettering is 130 mm long and 15 mm high. The 3D style (sticker is raised and made of thick plastic) gives the sticker a particularly high-quality look. Perfect for e.g. tank or side cover.The sticker consists of individual letters that sit firmly on a transfer film. This makes the sticker very easy to apply.
The lettering in black looks very good as a contrast on all other colors, as well as black on black on a black tank, for example.
The stickers are sold individually (i.e. the price is for one sticker).
Chain Set BlackLine - AC
CB12489M
/ RS-1
€179.95*
Attention! When ordering in the comments please specify for what a motorcycle and what year of manufacture the set should be. Only for models up to 2014 from 2015 other chains were installed (for this please contact us personally).
BlackLine 525 chain set.
For those who want it nice and black and inconspicuous, the black DID chain is just the thing. Black plates with silver rollers.The chain kit comes with a rivet lock.The kit also includes a chainring (either a black steel chainring or a Stealth chainring in gold/black) and a sprocket.
A bit further down in the description, you have to pack your desired gears to the set.
We recommend you to choose a shorter gear ratio than the original one from Triumph (this is simply much too long for the engine power). We advise a 18 / 45 or even 17 / 45 gear ratio.
Factory gear ratio:790cc engines: 17 / 43865cc engines: 18 / 43
Tip:- We recommend for safety a new sprocket lock plate with the chain set to order (see accessories article in this description).- In addition, you will find in the accessories still beautiful, black chainring nuts for all who want to have it completely black.
About the DID chain:
As the successor to the proven high-performance chain ZVM2, special attention was paid during the development of the ZVM-X to the diverse loads that occur in everyday life. The tensile strength only indicates the breaking load of a chain determined statically in the laboratory, but not the resistance to the forces that occur in practice.
For this reason, the ZVM-X focuses primarily on strength in use.
-increased tensile strength and-lower weight compared to the ZVM2-very high wear resistance and up to 50% reduced friction losses due to the patented X-ring technology.
Triumph Aluminum Tank Badge
CB12271
/ RS-1
€59.00*
CNC machined aluminum Triumph emblem. An absolute eye catcher on any Triumph machine! Because the letters stand individually and are raised, the emblem looks very classy and high quality.
The emblem is sold SEPARATELY! So who wants to have it left & right on his thanks, must order two pieces.
Long we have tinkered to develop a really cool Triumph emblem with individual letters that you can easily and straight stick on the tank or another place.
The emblem is milled from black anodized aluminum, which also creates the beautiful silver bevel.Glue is applied to the individual letters by hand after milling. A slightly thicker adhesive tape is used to compensate for inequalities and slight curvatures (e.g. that of a tank).
Included in the delivery is a mounting instruction and a device with which you get the letters also nice and straight and with the appropriate distance to each other glued.
Dimensions: 150mm long / 15mm high
Headlight Grill Alcatraz
CB12184.1M
/ RS-1
€109.00*
The Alcatraz grille is a precise German-made lamp grille that looks very solid & high quality and also protects your headlight from rough stone chips. Fits all air-cooled Triumph Modern Classic models.
Inspired by the famous American prison Alcatraz, the lamp grille is reminiscent of massive bars.
Made entirely of aluminum, the grille is laser cut in many individual parts & then welded by hand. Through the protruding individual struts, the grid gets a 3D look and does not just sit flat in front of the lamp, as is the case with most other grids.
The lamp grid is available in either black powder coated or silver glass bead blasted (this is a really classy, matte aluminum surface).The scope of delivery includes all screws & sleeves that are needed for mounting. In the black grille, the two visible screws left & right are also suitable in black.
Chain guard Ripped - AC
CB12386M
/ RS-1
€54.95*
Classicbike-Raisch Ripped aluminum chain guard suitable for the air-cooled Triumph Modern Classic models.
This chain guard was not simply copied from the original like most other accessory chain guards and then slightly modified visually. It was designed to run as flat as possible over the chain and has the same line as the swingarm to look visually optimal. Because both the original chain guards as well as most of the accessories, have a lot of air upwards to the chain. Nevertheless, our chain guard is granted that this does not get contact with the chain when driving.In addition, the protection is much shorter than the original which protrudes far beyond the sprocket. This looks visually much better and more harmonious. A good splash protection is thus widely granted.
The Raisch chain protectors are made of 2mm aluminum. The black chain protectors are powder coated, which ensures a deep black tone for years.
Underbar Mirror Kit Triumph Bonneville
CB12292M
/ RS-1
€119.00*
Motogadget Underbar Mirror Kit for Triumph Bonneville (air-cooled with 1-inch handlebars)
Looking for a clean and cool look for your air-cooled Triumph Bonneville? The Motogadget Underbar Mirror Kit makes your bike a real head-turner! Suitable for all models with original 1-inch handlebars and some aftermarket handlebars. And don't worry: the mirrors have an E-number and are road legal.
Flat & stylish line
These Underbar mirrors give your handlebars a really flat and tidy line. The mirrors are barely noticeable and thus ensure a minimalist, cool style. Thanks to the adjustable articulated joint, the mirrors can be positioned nicely flat and parallel to the handlebars – a really clean look that is easy on the eye.
And the best thing is: despite the unobtrusive look, you still have a good rear view – even better than with many standard accessory mirrors that are mounted at the top. The trick? You no longer look over your shoulder, but past your waist. The view is not quite as far-reaching as with the long original mirror arms, but it is ideal for urban use and a stylish appearance!
Scope of delivery & assembly
The scope of delivery includes a mirrorless Motogadget mirror with E-number, a black screw and a black cap nut to attach the mirror to the bottom of the original handlebar. There are three mirror variants to choose from, depending on your personal taste.
Important: You'll need a bit of skill when mounting the mirrors to ensure that the rear view is correct and that the mirror does not touch the tank when turning. Detailed assembly instructions are of course included!
The mirrorless mirrors from Motogadget
These mirrors are real high-tech works of art! They manage without any mirror glass at all – the patented reflective surface is integrated directly into the metal of the mirror body, so that the aluminium itself becomes the reflective surface. The result? An ultra-thin, rimless design without any unnecessary frames. Broken glass or falling mirrors are a thing of the past!
This extraordinary mirror design is truly a highlight and gives your bike a modern, exclusive touch.
Underbar Mirror Kit Scrambler AC
CB12293M
/ RS-1
€149.00*
Motogadget Underbar Mirror Kit for Triumph Scrambler (air-cooled)
Give your air-cooled Triumph Scrambler a modern and clean look with the Motogadget Underbar Mirror Kit! Fits the original handlebars and many accessory handlebars – naturally with E-number and approved for road use.
Flat, minimalist style for the handlebars
This mirror kit gives your handlebars a flat, uncluttered line and adds an extremely cool style to your Scrambler. Thanks to the adjustable ball joint, the mirrors can be positioned flat under the handlebars, keeping the upper handlebar area clean and clear. And although the mirrors are discreet, they offer a clear view to the rear. The highlight: instead of looking over your shoulder, you look past your waist, which makes it easier to see what's going on in city traffic.
Scope of delivery & customization options
The kit includes a Motogadget mirror without a mirror glass with E-number and a CNC-machined adapter. You can choose from three mirror variants. There are two versions of the adapter:
Please note: You will need an additional bracket for the brake fluid reservoir for installation. This can be found in the accessories for this product.
Installation instructions
A little patience is required when installing the mirrors to ensure that they are optimally adjusted and do not touch the tank when the handlebars are turned. Detailed installation instructions are included in the scope of delivery.
The mirrorless Motogadget mirrors – high-tech without glass
These mirrorless mirrors set new standards in design and functionality! They do not require any mirror glass. The patented mirror surface is integrated directly into the aluminum, enabling a frameless, ultra-thin design without a bezel. Broken glass or loose parts? Not a chance! These high-quality mirrors are lightweight and robust and are real eye-catchers on the road.
Note: The price is for 1 mirror + 1 adapter. Please select your desired version accordingly.
Raisch Leather Key Fob
CB11685M
/ RS-1
€7.95*
Classicbike-Raisch Vintage Leather Keychain with Brass Keyring.
A chic small motorcycle keychain with leather strap and stamped Classicbike-Raisch logo. The pendant is extra nice and short and not particularly heavy chosen, because it is in the ignition lock of the motorcycle and there should not cause any scratches.
Kineo for Bonnie & Scrambler
CB00351
/ RS-1
€2,886.00*
Hub colour:
Silver
|
Spoke Colour:
Silver (standard)
|
Spoke Nipples Colour:
Black
|
Wheel Colour:
Silver Glossy
Kineo Wheels for your Triumph Bonneville T100 & Scrambler 865Tubeless forged aluminum wheels
Upgrade your Triumph with Kineo Wheels, made in Italy. These precisely engineered, tubeless forged aluminum wheels impress not only with their first-class workmanship, but also with their outstanding appearance. With significantly better concentricity and noticeably less weight than the original wheels, they significantly improve the agility and handling of your motorcycle.
Weight advantage of Kineo wheels:
A weight of approx. 1.5–2.5 kg is saved per wheel.
Even if these numbers seem small, the lower weight plays a major role in rotating masses such as wheels. This leads to noticeably more dynamic handling and better acceleration.
In addition to their technical superiority, the Kineo wheels also offer a visual highlight: the intricately milled hubs and color-contrasting spoke nipples turn your motorcycle into an eye-catcher. The details are particularly effective when contrasting colors are chosen.
Ready-to-install wheel set with bearings & TÜV certificate
Dimensions front: 2.5 x19 inch
Dimensions at the rear: 4.25 x17 inch
The standard dimensions of the rims are the same as those of the original rims. Other dimensions are available at an extra charge (partly also at a discount). In principle, we can order the rims in all dimensions from Kineo.Please contact us in advance, as not all rim dimensions can be easily installed due to ABS and traction control.
Customize your Kineo Wheels! The rims are available in numerous color combinations. Just let us know your desired colors in the order comment or contact us for a personal consultation.
Note: Since the rims are made to your individual color requirements, the delivery time is about 6–10 weeks.
Dimensions
Rim size front
measure
additional charge
3.5x17
0 €
2.5x19
+ 21 €
Rim size rear
3.75x17
0 €
4.25x17
+ 27 €
5.0x17
+ 30 €
5.5x17
+ 24 €
To dye
rim
colour
additional charge
black Matt
0 €
White matt
0 €
shiny black
0 €
White shiny
0 €
Silver brushed
+ 95 €
Special colors: matt blue, gold matt,
Red matt & glossy, matt gray & glossy
+ 142 €
hub
silver
0 €
Shiny silver
0 €
black Matt
0 €
shiny black
0 €
Special colors: magnesium, titanium, gold,
Red, blue, green
+ 132 €
nipple
Black, silver, titanium, gold
Red, blue, orange, green
0 €
spoke
silver
0 €
black
+ 120 €
Silver / black alternating
+ 120 €
Kineo rims Triumph Thruxton
CB00352M
/ RS-1
€2,874.00*
Kineo Wheels for your Triumph Thruxton 865.Tubeless forged aluminum wheels
Upgrade your Triumph Thruxotn with Kineo Wheels, made in Italy. These precisely engineered, tubeless forged aluminum wheels not only impress with their first-class workmanship, but also with their outstanding appearance. With significantly better concentricity and noticeably less weight than the original wheels, they significantly improve the agility and handling of your motorcycle.
Weight advantage of Kineo wheels:
front: 1,2 kg
rear: 4,5 kg
Even if these numbers seem small, the lower weight plays a major role in rotating masses such as wheels. This leads to noticeably more dynamic handling and better acceleration.
In addition to their technical superiority, the Kineo rims also offer a visual highlight: the intricately milled hubs and color-contrasting spoke nipples turn your motorcycle into an eye-catcher. The details are particularly effective when contrasting colors are chosen.
Ready-to-install wheel set with bearings & TÜV certificate
Dimensions front: 2.5 x18 inch
Dimensions at the rear: 4.25 x17 inch
The standard dimensions of the rims are the same as those of the original rims. Other dimensions are available at an extra charge (partly also at a discount). Basically, we can order the rims in all dimensions from Kineo.For example, a Thruxton looks great with 17” rims at the front and rear with wide sports tires! If you are interested in other rim sizes, give us a call and we will be happy to help.
Customize your Kineo Wheels! The rims are available in numerous color combinations. Just let us know your desired colors in the order comment or contact us for a personal consultation.
Note: Since the rims are made to your individual color preferences, the delivery time is about 6–10 weeks.
Dimensions
Rim size front
measure
additional charge
2.5x18
0 €
3.5x17
+ 5 €
Rim size rear
3.75x17
0 €
4.25x17
+ 27 €
5.0x17
+ 30 €
5.5x17
+ 39 €
To dye
rim
colour
additional charge
black Matt
0 €
White matt
0 €
shiny black
0 €
White shiny
0 €
Silver brushed
+ 95 €
Special colors: matt blue, gold matt,
Red matt & glossy, matt gray & glossy
+ 142 €
hub
silver
0 €
Shiny silver
0 €
black Matt
0 €
shiny black
0 €
Special colors: magnesium, titanium, gold,
Red, blue, green
+ 132 €
nipple
Black, silver, titanium, gold
Red, blue, orange, green
0 €
spoke
silver
0 €
black
+ 120 €
Silver / black alternating
+ 120 €
Delivery time about 2-3 months
Streetbar Handlebar LSL
CB00176M
/ RS-1
€59.95*
LSL StreetBar handlebars in 1” or 22mm diameter.
These handlebars are fairly straight and quite flat, which on the one hand ensures a front-wheel-oriented seating position and on the other hand, and much more importantly, a really flat and cool look. I think the pictures speak for themselves here.
For model-specific descriptions, see below in the description.
You will need accessory handlebar end weights, as the original ones no longer fit.
Dimensions:- 1": 85 cm wide x 6 cm high - 22mm: 82cm wide x 5.5cm high
Heck Weck Kit
CB00468M
/ RS-1
€169.00*
Raisch rear wake kit for Triumph Bonneville, Thruxton & Scrambler. With this kit the bike gets a completely clean rear. Without the big original rear fender and without the original rear traffic lights made of plastic.The most minimalistic and elegant rear kit available on the market for these motorcycles!
Due to the rear under fairing (aluminum lower plate) there is a good splash protection. A LED license plate light with E-number is also included. License plate holder as well as subplate are precisely laser cut from aluminum in Germany & black powder coated.It also comes with a plug that fits into the original wiring harness. That is, only turn signals, lights, etc. must be crimped and can then be connected without having to change anything in the wiring harness.All other cables, connectors, screws, etc. that are needed for installation are of course also included.
Since the HeckWeck kit does NOT have a central tail light, it is mandatory to have 3in1 turn signals (these combine turn, tail & brake light in one turn signal).Further down in this description you can order the turn signals in a set and get 10% discount on the turn signals.All turn signals listed here are with E-number and street legal.
If you don't want to wire and crimp the enclosed cables, plugs & insulations by yourself, you can order this service as well (you can add it to the set below).
The Kit is available in 2 versions
Version 1: The turn signals are mounted with a retaining plate from the inside of the strut. When the ignition is off you almost think at the motorcycle are no turn signals on it (but you see them well enough when they light up. Is not so Stvo compliant, because the turn signals are too far in the rear.
Version 2: The turn signals are mounted directly on the license plate holder (turn signal holder are with the license plate holder). Legal and StvO compliant.
To have the kit 100% legal, a reflector must still be attached to the license plate (you can also find it below & add it to your kit).
Matching / same turn signals for front you will find at the very end of this description under the accessories.
Chain set - steel
CB00491M
/ RS-1
€119.95*
Chain set for Triumph Modern Classic - Bonneville / Thruxton / Scrambler
Attention! When ordering, please specify in the comments which motorbike and which year of manufacture the set should be for. Only for models up to 2014 from 2015 other chains were installed (please contact us personally)
Enuma 525 chain set optionally with steel chain (standard) or completely golden chain.
The kit includes a very high-quality Enuma chain, a chainring (either a black steel chainring or a stealth chainring in gold / black) and a chain sprocket.A little further down in the description, you have to add your desired sprockets to the set.A rivet lock is also included in the scope of delivery. If you don't have a rivet tool, we recommend ordering the patented Enuma screw lock (you can find it in the accessories section of this description)
We recommend that you choose a shorter gear ratio than the original Triumph (this is simply far too long for the engine power). We recommend an 18 / 45 or even 17 / 45 ratio.If you would like to order a different gear ratio than the one available, you are welcome to contact us and order a customised chainset.Factory gear ratio:790cc engines: 17 / 43865cc engines: 18 / 43
Tip:- To be on the safe side, we recommend ordering a new sprocket locking plate in addition to the chain set (see accessories article in this description).- You will also find beautiful black chainring nuts in the accessories section for those who want a completely black chainring.- For easier assembly, we recommend ordering the Enuma screw lock as well
About the Enuma chain:
There is nothing cheaper but nothing better. Quad-ring chain technology. Superior to the original DID O-ring chain.Thanks to the optional patented screw lock, quick and easy replacement without removing the swingarm or riveting. This saves time and money. Simply flex the old chain, fit the Enuma with screw lock and you're done. These chains are so strong that re-tensioning is almost unnecessary. Chainring and sprocket made from the best carbon steel.
Monza Tank Cap Kit
CB11046.1M
/ RS-1
€139.95*
The absolute classic fuel filler cap!A must for every retro fan. Extremely enhances the original tank of the motorcycle and is an absolute eye catcher.The beautiful Monza tank cap comes with a matching adapter for your Triumph tank. Mounting material, instructions and seals are of course also included.The tank cap is available in polished aluminium or matt brushed.
Note for models with original Monza fuel cap:For all models that have a Moza fuel cap installed as standard, an additional adapter ring is required to get a clean fuel cap (see accessories article in this description).
Monza Blackline Kit for Triumph
CB11735M
/ RS-1
€139.95*
The absolute classic fuel filler cap!A must for every retro fan. Extremely enhances the original tank of the motorcycle and is an absolute eye catcher.
The beautiful Monza tank cap comes with a matching adapter for your Triumph tank. Mounting material, instructions and seals are of course also included.
The Blackline tank caps are available in black or black with contrast polish.
Note for models with original Monza fuel cap:For all models that have a Moza fuel cap installed as standard, an additional adapter ring is required to get a clean fuel cap (see accessories article in this description).
Monza Bras Kit for Triumph
CB11736
/ RS-1
€189.95*
The absolute tank cap classic made of real brass for even more vintage look.A must for every retro fan. Enhances the original tank of the motorcycle extremely and is an absolute eye catcher.
If you like brass in vintage style more than polished, you can easily give the tank cap a VIntage look yourself.Just watch this video here and age your brass parts yourself.https://www.youtube.com/watch?v=sujyw-1Q_54
The beautiful Monza tank cap is shipped with a matching adapter for your Triumph tank. Mounting hardware, instructions & gaskets are of course also included. The assembly is very easy and done within a few minutes.
Note for models with original Monza tank cap:For all models that have a Moza tank cap installed as standard, an additional adapter ring is required to get a clean tank closure (see accessories article in this description).
Monza UK-Jack Kit for Triumph
CB12004.1M
/ RS-1
€149.95*
The absolute fuel cap classic in the new Union Jack design.A must for every retro fan. Extremely enhances the original tank of the motorcycle and is an absolute eye catcher.
The beautiful Monza fuel cap comes with a matching adapter for your Triumph tank. Mounting material, instructions & gaskets are of course also included.
Everyone knows the classic Monza tank cap. Now it is also available with a raised Unions Jack, which catches the eye with its milled lines.
Note for models with original Monza fuel cap:For all models that have a Moza fuel cap installed as standard, an additional adapter ring is required to get a clean fuel cap (see accessories article in this description).
Chain set - Gold
CB12878
/ RS-1
€119.95*
Chain set for Triumph Modern Classic - Bonneville / Thruxton / Scrambler - Gold
Attention! When ordering, please specify in the comments which motorbike and which year of manufacture the set should be for. Only for models up to 2014 from 2015 other chains were installed (please contact us personally)
Enuma 525 chain set optionally with steel chain (standard) or completely golden chain.
The kit includes a very high-quality Enuma chain, a chainring (either a black steel chainring or a stealth chainring in gold / black) and a chain sprocket.A little further down in the description, you have to add your desired sprockets to the set.A rivet lock is also included in the scope of delivery. If you don't have a rivet tool, we recommend ordering the patented Enuma screw lock (you can find it in the accessories section of this description)
We recommend that you choose a shorter gear ratio than the original Triumph (this is simply far too long for the engine power). We recommend an 18 / 45 or even 17 / 45 ratio.If you would like to order a different gear ratio than the one available, you are welcome to contact us and order a customised chainset.Factory gear ratio:790cc engines: 17 / 43865cc engines: 18 / 43
Tip:- To be on the safe side, we recommend ordering a new sprocket locking plate in addition to the chain set (see accessories article in this description).- You will also find beautiful black chainring nuts in the accessories section for those who want a completely black chainring.- For easier assembly, we recommend ordering the Enuma screw lock as well
About the Enuma chain:
There is nothing cheaper but nothing better. Quad-ring chain technology. Superior to the original DID O-ring chain.Thanks to the optional patented screw lock, quick and easy replacement without removing the swingarm or riveting. This saves time and money. Simply flex the old chain, fit the Enuma with screw lock and you're done. These chains are so strong that re-tensioning is almost unnecessary. Chainring and sprocket made from the best carbon steel.
Beeline Moto II Navi
CB12707M
/ RS0
€199.99*
The Beeline Moto Navigation System II is the smallest and smartest motorcycle navigation system available in the world.The new Beeline 2 is even more innovative, has more options, an improved display and an improved route display like the first series. In addition, the new system has glove-friendly buttons that are easy to operate even while driving.Visually, the Beeline sat nav is basically just a small black button that can be attached to and removed from the motorcycle in a matter of seconds.
Navigation with this navigation system works via an arrow and km indicators on the Beeline display. The special feature of this navigation system is that it has two different navigation modes:
1. classic precise navigation, in which an exact route is determined. Here the navigation system gives you an exact route with turn-offs, kilometers etc.
2. directional navigation in which the navigation device only gives you one direction. In this mode, the Beeline acts more or less like a compass. You give the navigation device a destination and it only shows you one direction to drive in via the arrow. In my opinion, this is a very cool way of navigating for motorcycles. Because with a motorcycle, the journey is usually the destination and the rider can decide their own route and keep their nose to the wind as they please.
The routes are set using a smart phone and the appropriate Beeline navigation app.
Be sure to watch the video at the end of the description to get to know all the functions of the Beeline Navi!
Another very good thing about the navigation device is the long battery life of 14 hours.It is also possible to order an additional charging adapter so that the navigation device can be charged on the motorcycle and used indefinitely (see accessories in this description)
A mounting system is included in the scope of delivery (the Strap Mount System. You can also find the article under the accessories in this description if you want to read more about how these mounts work).3 other mounting options are also available (these can also be found under accessories in this description).
Versions: In the black version, the case is made of plastic. In the silver & gunmetal version, the case is made of metal.
Included in delivery:
1 BEELINE Moto 2 navigation device 1 "Universal strap mount" navigation holder1 USB charging cableFits all motorcycles and scootersWaterproof and shockproofTwo navigation modesFour buttons (glove-friendly)Diameter of the active area: 30 mmWorldwide coverage (Google Maps)Record & share ridesStrava integration & GPX importAutomatic backlight for night ridesLifetime app and firmware updatesApp supports the following languages: English, German, French and JapanesePhone requirements:
iPhone - iOS 9.2 and aboveAndroid phone with Google Play - 8.0 Oreo and aboveBluetooth 4.0 capability required
Battery
Capacity: 600mAhBattery operating time: 14 hours in operationMicro USB chargingDisplay
Technology: Ultra-bright IPS TFT display with anti-reflective and hydrophobic coatingSize: 36.8mm (1.45") screen diagonal, 10cm total areaResolution: 412x412 (402ppi)Navigation
Intelligent turn-by-turn navigation with estimated time of arrival and speed information.Classic arrow display in route and compass mode.Turn-by-turn directions: Warning LED and signal tone (spoken warnings via the app - currently only via BeelinePlus)
Additional functions
Speed limit display (depending on location)Record and share journeysGPX route import/exportSupports 8 languagesFun and fast route planning (depending on location)
Beeline Moto II - Power / Strom Adapter
CB12712
/ RS0
€54.99*
Endless power! With this insert, any compatible mount* can be converted so that the Moto II can be easily charged while riding.
Easy installationDirect connection to the 12V battery terminalsAdjustable orientation with top or bottom cable outletWeatherproof, sealed construction with replaceable contact pinsAutomatic power switching to avoid dead batteries*Not compatible with universal mount
Included in delivery
Powered mount insertExtended bolts for mounting2m 12V battery connection cable2x cable ties
Notes
With this Powered Mount insert, the Moto II device can be charged while riding. It is designed to be connected to the motorcycle battery with ring terminals in the same way that other accessories are connected to motorcycles, e.g. heated grips.
The design allows all mounts (except the universal mount) to be adapted to power the device. To install, the original mount insert must be removed from the bracket, then the Powered Mount insert is fitted in its place. The Powered Mount insert is supplied with three different screws that can be used to attach it to the different brackets.
The insert uses pogo pins to charge the device via contacts on the underside. The design is made to avoid corrosion problems that can often occur with this type of charging mount for navigation devices. Corrosion can occur if the mount is left outside in bad weather for long periods of time.
The Powered Mount insert can be installed so that the cable exits from either the top or bottom. A rectifier chip in the device allows both contacts to accept positive or negative charge.
Unit Garage - Tank bag - Canvas
CB12689M
/ RS0
€399.95*
A really nice, classic tank bag made from canvas/sailcloth.
Quality / Fastening / 2-1 tank bag & backpack
This VERY high-quality tank bag focuses on the essentials for a tank bag paired with a very nice design. The tank bag is attached to the motorcycle in the classic way with 2 straps, guaranteeing a very secure and firm hold. The straps are fitted with a cover that makes it possible to conceal the metal straps.When removed from the motorcycle, the tank bag can also be used as a normal rucksack, which is particularly practical on tours or short trips. This gives you the option of not leaving your valuable belongings on the motorcycle when you are away from it.
Water-repellent / care
The backpack is made of thick / very high-quality canvas fabric. The fabric is lightly waxed and therefore slightly water-repellent (not waterproof). This can be reinforced with a waterproofing spray. Suitable waterproofing spray and wax (to care for the bag so that you can enjoy it for a long time) can be found under accessories in this product description.
Storage space
The tank bag has two pockets that are accessible from the outside and can be opened with a high-quality metal zipper. There is also a small additional pocket on the side where you can stow things that you need to have to hand quickly (e.g. sunglasses / cash etc.).Inside the main compartment there is a separate compartment that offers space for documents or a laptop (up to 15"), for example.
Dimensions
Dimensions: Length 42cm, width 31cm, height 14cmVolume: 23 litersWeight: 2.15kg
Unit Garage - Tank bag - Suede leather
CB12690M
/ RS0
€439.95*
A really beautiful, classic tank bag made from genuine suede
Quality / Fastening / 2-1 tank bag & backpack
This VERY high-quality tank bag focuses on the essentials for a tank bag paired with a very beautiful design. The tank bag is attached to the motorcycle in the classic way with 2 straps, guaranteeing a very secure and firm hold. The straps are fitted with a cover that makes it possible to conceal the metal straps.When removed from the motorcycle, the tank bag can also be used as a normal rucksack, which is particularly practical on tours or short trips. This gives you the option of not leaving your valuable belongings on the motorcycle when you are away from it.
Water-repellent / care
The backpack is made of thick / very high-quality canvas fabric. The fabric is lightly waxed and therefore slightly water-repellent (not waterproof). This can be reinforced with a waterproofing spray. Suitable waterproofing spray and wax (to care for the bag so that you can enjoy it for a long time) can be found under accessories in this product description.
Material
The Unit Garage tank bag (handmade in Italy) is made from 3mm thick, extremely high-quality genuine leather. The high-quality material guarantees that the backpack will last a lifetime if cared for properly.
Storage space
The tank bag has two pockets that are accessible from the outside and can be opened with a high-quality metal zipper. There is also a small additional pocket on the side where you can stow things that you need to have to hand quickly (e.g. sunglasses / cash etc.).Inside the main compartment there is a separate compartment that offers space for documents or a laptop (up to 15"), for example.
Dimensions
Dimensions: Length 42cm, width 31cm, height 14cmVolume: 23 litersWeight: 2.15kg
Custom Cap - Flat
CB12686
/ RS0
€99.95*
The Jetson tank cap made of cast aluminum in a flat design. We have been selling the custom cap fuel filler cap very successfully for years. Now there is also the completely black flat version, which has a slightly different design and is significantly flatter.
The tank cap is supplied complete with thread and seal. This means it can be replaced one-to-one with the original without having to modify anything.
The ribbing not only gives the cap a nice look, but also makes it very easy to grip.
Motone also offers an oil filler cap in the same design as a matching accessory (can be found under accessories in this product description).
LED headlight - Stripe
CB12673M
/ RS0
€259.95*
The Stripe LED headlight insert is a very attractive and simple insert that offers very good light output at a fair price!
The simple and clear design fits perfectly with our Modern Classic motorcycles. The clear glass gives your motorcycle a slightly modern touch without attracting negative attention with an overly restless design.
The light is a quantum leap compared to a conventional H4 halogen bulb! If you ride your motorcycle in the dark, you should invest some money in good lighting. On the one hand, you can see much better yourself because the road is properly illuminated, and on the other hand, you will also be seen better.
We supply the headlight in such a way that it can be installed plug & play in the original headlight of your Triumph. A glass base adapter is also required for the connection. This can be found under accessories in this description.
Tank bag - Navigator
CB12665M
/ RS0
€59.95*
The Navigator tank bag is a practical small backpack for short trips.The tank bag combines a practical cell phone compartment (with transparent film to use the cell phone for navigation) with a small, practical pocket in which you can store the essentials for a day trip (wallet/keys etc.). The navigator is held to the tank with 6 strong magnets, so there is no need to attach it (just the thing for a bag that you spontaneously take with you for a short trip).
The bag is made of heavy canvas combined with leather: Waterproof zippers and heavily waxed materials ensure that the bag can withstand a downpour without getting wet on the inside (it probably can't withstand constant rain).
Dimensions of the bag: 22 x 12.5 x 7.5 cm (large enough for an iPhone Max).
In addition to being used as a tank bag, the bag can also be used as a belt bag or shoulder bag (with the supplied strap).This is very practical if you want to take your valuables with you when you are away from the bike for a while on tour.
Perforated grip tape
CB12656M
/ RS0
€41.95*
That's oldschool! Handlebar grips which are wrapped from genuine leather tape!That was otherwise only possible with a lot of manual work (and high costs) with a upholsterer.Now there is leather tape to wrap for everyone! The tape is equipped with 3M adhesive tape on the inside, so it simply sticks to the handlebar when winding. The tape is simply wrapped directly onto the handlebar & grass grip sleeve (if you don't want the grip so thick), or over the existing grip rubbers.The tape is pre-cut at the ends to fit, so that a nice winding pattern is easily added.
We also have many other leather things, made of the same leather, in our shop. For example real leather handles (see similar articles in this description).Here's a video on how to wrap the ribbon in the best possible way.
License plate holder - Shock AC
CB12637
/ RS0
€99.95*
Classicbike-Raisch Shock mount license plate holder. The simple solution for mounting the license plate on the side of the shock absorber. A side-mounted license plate gives your Triumph a completely free / clean rear end.
The stainless steel base holder is simply pushed behind the shock absorber over the spike and attached together with the shock absorber. Installation is very simple and can be completed in a short time (installation instructions are included).
The license plate can be individually moved inwards and outwards using slotted holes in the base holder and 4 differently positioned holes in the license plate. If the license plate is pushed all the way out, the license plate holder can be registered individually. The scope of delivery includes LED license plate lighting and all necessary mounting materials.
Tips for a complete rear conversion: In order to have a completely beautifully converted rear end on your Triumph, the bulky original mudguard must of course also be removed! We offer you two options for this.Option 1: You remove the original mudguard completely and replace it with our underbody plate. (As shown in the product pictures)Option 2: You install a shorter & narrower aluminum mudguard
New Indicator brackets must also be fitted if the original mudguard is removed.
The accessories described can all be found under the accessory items in this product description.
Sump guard - Ripped
CB12633.1M
/ RS0
€99.95*
Your Triumph deserves the best protection - our underride guard in ripped design is the perfect balance between protection for your motorcycle and a classic design that makes your Triumph more beautiful.
Made in Germany
The engine guard protects the frame and the body of your motorcycle from rough stone chipping and if you ever hit the ground.
But the guard also looks great. It skillfully closes the gap between the two frame struts. The gripped design looks beautifully classic. If you are primarily looking for the best possible protection for your motorcycle, we recommend our closed "Triumph underride guard" (see similar products in this description).
Black / Silver:
In the black version, the protection is supplied powder-coated
In the silver version, the protection is supplied in raw aluminum (perfect for brushing or polishing)
Why our underride guard:
Unique ripped design
High-quality aluminum for the best protection
Stylish look that gives your motorcycle that little bit extra
Sump guard - Triumph
CB12634M
/ RS0
€99.95*
Your Triumph deserves the best protection - our Triumph Triangula underride guard is the perfect balance between protection for your motorcycle and a classic design that makes your Triumph more beautiful.
Made in Germany
The engine guard protects the frame of your motorcycle from rough stone chips. It also protects against accidental impact.
But the guard also looks great. It skillfully closes the gap between the two frame struts. The implied T and the Union Jack flag in the guard perfectly match our English Triumph bikes.
Black / Silver:
In the black version, the guard is supplied powder-coated
In the silver version, the guard is supplied in raw aluminum (perfect for brushing or polishing)
Why our underride guard:
High-quality aluminum for the best protection
Stylish look that gives your motorcycle that little bit extra
All necessary mounting materials are included in the scope of delivery
Fork head caps - Triumph Milled
CB12580M
/ RS0
€89.90*
CNC-milled black aluminium fork end caps for the forks of your Triumph Modern Classic machine.
The milled fork end caps replace the original silver caps and are easy to fit.
The caps are simply exchanged for the originals in a few minutes. The fork does not need to be removed for installation (it just needs to be relieved of load, e.g. by jacking up the motorcycle or having a second person lift it up over the side stand) and no special tools are required. Installation instructions are included,
The milled caps are manufactured with a very elegant black pearl surface. This means that they are blasted with glass beads before black anodising. This results in a very fine, slightly matt surface that feels very high quality and looks very elegant.The silver accents are then milled afterwards.
Classicbike-Raisch recommendation: Order the plastic tool as well, so that it is very easy to mount the milled caps without scratches and blemishes (see accessories in this description).Note on Bobber & Speedmaster with 47mm forks:To remove the original fork caps on these models, you have to remove the fork bridge, otherwise you cannot access the fork cap with any tool. With our special plastic socket, you can do this easily without dismantling the fork bridge. This saves time and not everyone has a 36mm socket in their toolbox.
Note for Speed Twin 1200 Euro 5:To remove the original fork cap of the Speed Twin 1200, you need a very large nut. Because almost no one has such a tool, a plastic nut is included in the kit. It also includes a plate that makes installation even easier. Detailed instructions are included in the scope of delivery.To ensure that the new black fork cap is fitted correctly, we recommend that you also order the assembly tool (accessory).
LSL Pace - X Griffe - 22mm
CB11388M
/ RS0
€39.95*
LSL PACE-X Lenkergriffgummi mit abnehmbarer Endkappe für 22mm Lenker.
Der LSL PACE-X Alu/Gummigriff sorgt für ein sicheres, gutes Griffgefühl am Lenker. Es ist ein universeller Gummigriff für Lenker mit 7/8 Zoll (22,2 mm) Rohrdurchmesser im attraktiven Look.Die eingearbeiteten Aluminium Elemente an den Griffen sorgen für eine elegante Optik und eine sehr hochwertige Haptik und das zu einem unschlagbaren Preis.
Zubehör-Tipp:Dank der abnehmbaren Endkappen der Griffe, lassen sich diese wunderbar mit Lenkerenden Blinkern & Spiegel kombinieren.
Maße:• Länge: 125 mm• Außendurchmesser Gummi ca: Ø32 mm• Außendurchmesser Aluhülse: ca. Ø40 mm• Innendurchmesser Gummi 1 ca: Ø20 mm• Innendurchmesser Gummi 2 ca: Ø23 mm
Lieferumfang: 1 Paar• 1x Griffgummi für die linke Seite• 1x Griffgummi für die rechte Gasgriff-Seite
Rizoma Grips sport 22mm
CB12567M
/ RS0
€80.00*
Rizoma Sport handles in 22mm made of billet aluminum. With integrated rubber, the soft rubber and the many small nobles, the handles offer a particularly good grip.
For BMW R9T models: Extra adapters are required for installation (see accessories in this description).
Chain Guard Kit - Short AC
CB12534
/ RS0
€79.95*
Classicbike-Raisch aluminum chain guard in the Short version - Made in Germany.
The Short chain guard kits define a chain guard completely new. As minimalist as possible and running close to the chain, they provide a radical design and fulfill their most important purpose (not to get into the chain).In the chain guards is the design aspect absolute priority and not the splash protection (true to the motto: Who wants to be beautiful must suffer). A reasonably lubricated chain with modern, high-quality chain grease (such as the Motul Chain Lube) from our range but also do not splash much.
In the kits, everything is included that is needed for assembly.Depending on the model, the scope of delivery still includes an additional chain guard fin, which is mounted in the middle of the swingarm to guarantee protection here as well.
The Raisch chain guards are made of 3mm aluminum in Germany and then black powder coated.
Light Guid LED tail light.
CB12522
/ RS0
€44.95*
Suitable accessory tail light for the rear Eliminator Kit.
DimensionsWidth: 84 mmHeight: 25 mmDepth: 37 mm
Mounting screws: 2 x M4 (rear of housing)
Connections: Green cable = ground (-)Yellow cable = rear light (+)Blue cable = brake light (+)
Unit Garage - Leather Bags Crust
CB12497M
/ RS0
€449.95*
A very stylish suede motorbike side bags handmade in Italy by Unit Garage.Available in two sizes: 10-14 litres / 22-30 litres.
In the set together with a side pocket holder (can be ordered directly below the description) there is a 12,5% discount on the entire set!
The suede bags have a waxed surface (we recommend waxing & waterproofing the bags once a year, you can order the appropriate wax & spray below the description), which ensures that the bags are water-repellent. If you want to be on the safe side for tours and don't want to get your clothes wet in heavy rain, we recommend ordering a Unit Garage rain cover or Khali inner bag (can be ordered below). We use the highest quality leather available in Italy, 3mm thick.
The Unit Garage bags do not only look cool, they are also extremely practical and good motorbike side bags. The bags have a quick release fastener on the back, which allows the bags to be attached to the Unit Garage side bag holder in one easy step (You can order the matching bag holder for your motorbike directly below the description in the set.). In addition, a lock is integrated into the quick-release fastener, which protects the bag against theft.
The bags have a practical outside pocket for things that you need to access very quickly, and a shoulder strap for carrying the bag is also included.
Details of the 10-14 litre bag: Dimensions: height 32 cm, extendable to 45 cm, width 24 cm depth 13 cm.Volume: 10-14 litresWeight: 2,2 kg This bag can hold a 15-16 inch laptop.
Details of the 22-30 litre bag: Dimensions: height 35 cm, extendable in height up to 50 cm, width 32 cm, depth 20 cm.Volume: 22-30 litresWeight: 2,75 kgThe large version of the bag has a removable inner core, which ensures that the bag keeps its shape even when there are no contents in the bag.You can fit a jet helmet in the bag.
Unit Garage - Canvas bags
CB12498M
/ RS0
€409.95*
A very stylish canvas / cotton linen motorbike side bag handmade in Italy by Unit Garage.Available in two sizes: 10-14 litres / 22-30 litres.
In the set together with a side pocket holder (can be ordered directly below the description) there is a 35 % discount on the holders!
The canvas bags have a waxed surface (we recommend re-waxing & waterproofing the bags once a year, you can order the appropriate wax & spray below the description), which ensures that the bags are water-repellent. If you want to be on the safe side for tours and don't want to get your clothes wet in heavy rain, we recommend ordering a Unit Garage rain cover or Khali inner bag (can be ordered below).
The Unit Garage bags do not only look cool, they are also extremely practical and good motorbike side bags. The bags have a quick release fastener on the back, which makes it possible to attach the bags to the Unit Garage side bag holder with just one movement (You can order the matching bag holder for your motorbike directly below the description in the set.). In addition, a lock is integrated into the quick-release fastener, which protects the bag against theft.
The bags have a practical outside pocket for things that you need to access very quickly, and a shoulder strap for carrying the bag is also included.
Details of the 10-14 litre bag: Dimensions: height 32 cm, extendable to 45 cm, width 24 cm depth 13 cm.Volume: 10-14 litresWeight: 1,45 kg This bag is big enough to hold a 15-16 inch laptop.
Details of the 22-30 litre bag: Dimensions: height 35 cm, extendable in height up to 50 cm, width 32 cm, depth 20 cm.Volume: 22-30 litresWeight: 1,90 kgThe large version of the bag has a removable inner core, which ensures that the bag keeps its shape even when there are no contents in the bag.You can get a jet helmet inside the bag.
Unit Garage - Khali bags
CB12499
/ RS0
€289.95*
Modern unit garage TPU plastic side bag that is 100% waterproof.20-26 litre capacity.Equipped with the Unit Garage quick release fastener on the back of the bag, it is attached to the Unit Garage side bag holders.
In a set together with a side bag holder (can be ordered directly below the description) there is a 35 % discount on the holders!
The Unit Garage bags not only look cool, they are also extremely practical and good motorbike side bags. The bags have a quick-release fastener on the back, which makes it possible to attach the bags to the Unit Garage side bag holder with just one movement (you can order the matching bag holder for your motorbike below the description in the set).In addition, a lock is integrated into the quick-release fastener, which protects the bag against theft.
The bags have a practical outside pocket (accessible via a waterproof zip) for things that you need to access very quickly, and a shoulder strap for carrying the bag is also included.
Materials: High frequency heat sealed TPU with Hypalon surfaces.- TPU is the latest generation material that makes PVC obsolete. It is a composite material with excellent elasticity & wear resistance.- TPU is a highly technological, durable material with excellent waterproofing properties that is resistant to weathering, chemicals and UV rays.
- Roll-up closure that guarantees waterproofness.- Magnetic buckles (quick release)- Reflective inserts for better visibility- Straps with Velcro fastening to secure the excess part- Rigid reinforced back to keep the bag in shape- Shoulder strap and handle included
Dimensions: Height 38 cm, extendable in height up to 48 cm, width 30 cm, depth 18 cm.Volume: 22-26 litresWeight: 1,25kg
Pico LED Turn Signal
CB12469
/ RS0
€139.95*
A PAIR Pico aluminum LED turn signals from the brand Motone from England. With E-number & road approval.
The very high quality Motone turn signals are made of a full metal housing and have an Osram SMD LED insert.
The Pico turn signals are the only turn signals in our range, where the cables are sheathed with a fabric hose and also have a sleeve included with which the nut / thread is covered. This is visually and haptically really nice! The turn signals have an M8 thread & have a 3.9mm Japan plug at the cable ends. Under the accessories in this description you will find model specific turn signal plugs for your motorcycle.
The Pico turn signals have a classic bullet design and are the absolute perfect size for our Modern Classic bikes. They are nice and small, but not too tiny. Dimensions: W 18 x H 44 x D 25.5 mm
Pico LED 3-1 tail light / indicator combination
CB12483
/ RS0
€159.95*
A PAIR of Pico aluminium LED 3 in indicator / rear / brake light combination from the Motone brand in England. With E-number & road approval.
The very high quality Motone indicators are made of a full metal housing and have an Osram SMD LED insert.
The Pico 3 in 1 turn signals are the only turn signals in our range where the cables are encased in a fabric tube and also have a sleeve included to cover the nut / thread. This is visually and haptically very nice! The turn signals have an M8 thread & have a 3.9mm Japan plug at the cable ends. You will find model-specific indicator plugs for your motorbike under the accessories in this description.
The Pico 3 in 1 turn signals have a classic bullet design and are the perfect size for our Modern Classic bikes. They are nice and small, but not too tiny either. Dimensions: W 18 x H 44 x D 25.5 mm
Classicbike-Raisch tips:Accessory indicators are always supplied by the manufacturers with universal plugs or completely without plugs. If you simply want to connect the indicators to the original wiring harness of your motorcycle, you can also order suitable blinker plugs for your motorcycle (you will find the plugs under the accessory items in this description).
Our years of experience have shown that unfortunately there is no rule as to which motorcycle models require a turn signal resistor and which do not. So if you want to be 100% sure that the indicators flash at the correct frequency after converting to accessory indicators, we recommend buying a set of resistors (you can find them under accessories in this description).
Timing belt drive kit - AC
CB12454M
/ RS0
€855.00*
Timing belt drive kit for the air cooled Triumph Modern Classic models.
The timing belt drive is primarily to reduce the loss of power from the transmission output to the rear wheel. It also makes the usual chain maintenance a thing of the past. No more chain tensioning, no more chain lubrication, and most importantly, no more chain grease/dirt removal from the bike.
The gear ratio of your motorcycle remains the same after the conversion.
Attention:
The kit is not a very easy to install plug & play kit. Please have a look at the assembly instructions before buying (you can find them under downloads in the product description).The original chain guard and the sprocket cover can not be used. A matching belt guard and sprocket cover, you will find under the accessories in this description.
Model specific descriptions:
Bonneville - pulley: 65 teeth / sprocket: 27 teeth / belt: 130 teeth
Thruxton / Scrambler - Pulley: 65 teeth / Pinion: 27 teeth / Belt: 132 teeth
Speedmaster / America - pulley: 65 teeth / sprocket: 27 teeth / belt: 140 teeth
Classicbike-Raisch tip: We recommend ordering the matching adjuster for perfect belt tension adjustment (see accessories in this product description)
Triumph - Milled Bremsdeckel
CB12609M
/ RS0
€55.95*
Triumph Milled Bremsbehälter Abdeckung by Classicbike-Raisch.CNC gefräste Aluminium Ausgleichsbehälter Abdeckungen für alle Triumph Modern Classic Modelle mit 1 Zoll Lenker.
Die Deckel werden im 3D Fräsverfahren in Deutschland hergestellt. Im Nachgang werden sie Glasperlen gestrahlt und schwarz eloxiert. Dadurch bekommt man eine unglaublich wertige, raue Oberfläche, die auch perfekt zu den original Armaturen der Triumph Modelle passt.Außerdem hat das den Vorteil, dass die Oberfläche einen noch tieferen Schwarzton bekommt und diesen auch noch nach vielen Jahren hat.
Das angedeutete T Logo mit integrierter Union Jack Flagge lässt dich beim Fahren daran erinnern, dass du eine Triumph, ein Englischer Klassiker mit Tradition fährst.
Die Ausgleichsbehälter Abdeckungen werden ganz einfach gegen die originalen ausgetauscht, was in wenigen Minuten erledigt ist.
Optional könnt ihr euch noch schwarze Schrauben dazu bestellen, diese findet ihr unter den Zubehörartikeln in dieser Produktbeschreibung.
%
Motul motorcycle care set
CB12433
/ RS0
€89.95*
€109.35*
(17.74% saved)
The Motul care set contains everything you need for the thorough care of your motorcycle.True to the motto who loves his motorcycle cleans!
In the set are the following things included:
2x Raisch microfiber cleaning cloth: A very absorbent microfiber cloth. A cloth to wash your motorcycle and a cloth to dry.
1x Microfiber Premium Cleaning Cloth: Probably the best cloth we have ever had in our hands. Optimal for quick care, if your bike is just a little dusty. Once wipe over it and everything is gone.
1x premium drying cloth: This cloth only needs to be walked over a wet surface once and it absorbs all the water (see video below)
1 liter Motul Moto Wash Motorcycle Cleaner
400 ml Motul Rim Cleaner
400 ml Motul Insect Remover
400 ml Shine & Go Silicone Spray (After cleaning the bike, spray on the engine block, metal parts as well as plastic parts and your bike will look like a new bike again)
400 ml Motul Wash & Wax (Paint finisher and fast cleaner. Apply to the varnish, let it work for 1-2 minutes and wipe it off).
In the set for a special price!
%
Motul chain care set
CB12438M
/ RS0
€37.95*
€42.70*
(11.12% saved)
Motul Chain Clean Set contains:
400ml Motul Chain Clean: Even the chain on a well-kept motorcycle should be cleaned regularly. So that this A lasts long and B the motorcycle looks gepfelgt.
400ml Motul Chain Lube: Chain grease for regular chain maintenance. The Motul Chain Lube Spray is a transparent spray, which should be applied thinly and thus the motorcycle (swingarm, chain guard, sprocket cover, etc.) not messed up as some other chain sprays.
150ml Chain Paste: Chain Paste to smear for the quick chain lubricate in between, if times no helper is available.
In the set at a special price!
Gasket set sprocket carrier
CB12408
/ RS0
€29.95*
A very well-known weak point on the air-cooled Twins is the sealing of the sprocket carrier.
The original aluminum bushing runs in very quickly, the sealing lip of the oil ring dissolves and there is no longer a proper seal. The result is water penetration and Gammel, especially at the ligendem bearing behind it.Our sealing kit provides a remedy. The bushing is made of stainless steel and no longer runs in. A new oil seal is of course included. Also included is a new circlip for the bearing behind the oil seal, as this is often also rusted.We recommend to install the seal set in principle, to prevent consequential damage to the bearing.In very acute cases, the bearing even dissolves into its individual parts (picture shows a completely destroyed bearing, we came the balls of the bearing even when dismantling the wheel. Machine had run good 50tkm)Who still needs a new bearing or just want to renew it at the same time: Further down under accessories order the same!
Turn signal holder fittings
CB12406
/ RS0
€27.95*
A pair of black powder coated aluminum turn signal holders (made in Germany), which are mounted below the Triumph brake & clutch armatures.
The holders are designed to mount the Kellermann Atto turn signals (the turn signals can be found under the accessories items in this description).
With the holders the given turn signal distance of 240mm is kept on all Triumph models. The Atto turn signals can therefore be mounted with the armature holders very inconspicuous and legal on your Triumph.
The scope of delivery includes everything needed to attach the holders to the fittings. Screws, sleeve, heat shrink tubing & assembly instructions.
%
Beeline Moto Navi
CB12245M
/ RS0
€149.00*
€179.00*
(16.76% saved)
The Beeline Moto navigation system is the smallest and smartest motorcycle navigation system available in the world.Visually, the Beeline Navi is virtually just a small black button, which you have within seconds on the motorcycle and off again.
The navigation of this navigator works via a file and km displays on the display of the Beeline. The special thing about this navigation system is that it has two different navigation modes:
1. classic exact navigation, where an exact route is determined. Here, the navigator gives a precise route with turns, km information, etc..
2. directional navigation, where the navigator gives only one direction. In this mode the Beeline works like a compass. You give the Navi a destination and it shows you via the arrow only one direction in which you have to go. In my opinion, this is a very cool way to navigate for motorcycles. Because with the motorcycle is usually the way the goal and the driver can think about his own route and hold his nose at will in the wind.
The routes are set with a smart phone and the appropriate Beeline navigation app.
Be sure to check out the video at the end of the description to get to know all the features of the Beeline Navi in detail!
Another very good thing about the Navi is the long battery life of 30Std.
In the scope of delivery are 2 mounting systems included (1x the Sticky Pad Mount System / 1x the Strap Mount System. Both items can also be found under the accessories in this description, if you want to read in more detail how these mounts work).3 Other mounting options are also available (you can also find these under the accessory items in this description).
Finishes: In the black version, the case is made of plastic. In the silver & gunmetal version, the case is made of metal.
Included in delivery:
1 navigation device BEELINE Moto in black
1 navigation mount "Sticky Pad
1 navigation mount "Universal Strap Mount
1 USB charging cable
Fits all motorcycles and scooters
Waterproof and shockproof
Two navigation modes
Four buttons (glove friendly)
Diameter of active area: 30 mm
Worldwide coverage (Google Maps)
Record & share rides
Strava integration & GPX import
Automatic backlight for night riding
Lifetime app and firmware updates
App supports the following languages: English, German, French and Japanese
Mobile Phone Requirements:
iPhone - iOS 9.2 and above OR Android phone with Google Play - 7.0 Nougat and above.
Bluetooth 4.0 capability required
Battery
Capacity: 400mAh
Battery operating time: without backlight: 30 hours - with backlight: 10 hours - mixed: 20 hours
Battery life in standby: 2-3 months
Micro USB charging Translated with www.DeepL.com/Translator (free version)
Pantera Forkcover Springs
CB12139M
/ RS0
€90.00*
A pair of fork springs that work like our well-known fork covers. These are inserted between the upper and lower triple clamp. So you get the look of a classic Springer fork. That is times oldschool!
For assembly, the upper triple clamp must be taken down and then the springs are simply pushed over the fork tube.
Mandatory is that you have a headlight mounted, which is attached centrally and not with lamepnhaltern, which sit as original on the fork. (Suitable headlights see accessories article in this description).
Note Thruxton: Who wants to mount the springs on a Thruxton, it must shorten a small piece.
Dimensions: 20x6x6 cm
Jarama Seat
CB12135.3M
/ RS0
€440.00*
Jarama Seat from Tamarit Motorcycles fits all air cooled Triumph Modern Classic models.The seat gives your Twinden look of a real, classic cafe racer. Photos say more than words here I would say.Looks especially good in combination with our HeckWeck Kit.
The bench is simply plug&play against the original seat and attached with the same two screws.
As with all Tamarit parts, the Monaco Seat is handcrafted from the best materials available. The Jerez seat is made of fiberglass, polyurethane and nautical fabric. All these materials are weather resistant.So upholstery is a high quality foam for the most comfortable seat possible, despite the thin cushion.The leather is one of the highest quality leatherette available. Visually, there is virtually no difference to real leather. However, imitation leather has the advantage that it is easier to care for and does not get wet in the rain.The cover is available in black or brown. The upholstery is particularly eye-catching due to its unique quilted pattern.
Dimensions of the seat: 74x28x16
The Monaco Seat can be ordered either in unpainted (Raw) or gloss black (Jet Black).
Fitting clamp with mirror thread Triumph Milled
CB12227
/ RS0
€39.95*
This CNC machined aluminum clamp replaces the original armature clamps. Fits all Triumph models with 22mm handlebars.
The clamps look much nicer on the one hand, because they are milled very high quality aluminum and have a beautiful, indicated T - logo. The mirror thread is M10 x 1.25 which allows you to mount all common mirrors from the accessories market as well as the original. Some models, such as the Triumph Speed Twin & Thruxton R, have no mirror thread from the factory (because they have handlebar end mirrors mounted). If you want to mount a normal mirror on such a model, you need a new adapter with thread.
Of course, such a milled clamping is not noticeable at first glance on the bike, but exactly on this area you look as a driver when driving all the time.
The adapters are black glossy (matching the original fittings) anodized & in the aftermath, the T - logo is milled again. The clamps look very classy on the handlebars.
The threaded adapter for the mirror we have extra round Designed, which gives you a much nicer transition to most mirrors, as with most other adapters on the market, which are simply angular. To the Motogadget M.View mirrors, the transition is perfect.
The adapters are sold individually.
Fitting clamp without mirror thread Triumph Milled
CB12228
/ RS0
€39.95*
This CNC machined aluminum clamp replaces the original armature clamps. Fits all for all Triumph models with 22mm handlebars.
This makes sense when you convert the motorcycles to handlebar end mirrors, because otherwise you look at the open mirror thread of the original clamp.
In addition, the clamps make optically also really what her through their high-quality surface and the milled T - logo. Of course, this is not noticeable at first glance on the bike, but exactly on this area you look as a driver when driving all the time.
The adapters are black anodized & in the follow-up, the T - logo is milled again. The clamps look very classy on the handlebars.
The adapters are sold individually.
Rizoma Mutation P1 Grips
CB12103
/ RS0
€35.00*
The 22mm Rizoma Mutations grips are made of very high quality elastomer plastic.
The design is such that the grips provide the rider with the best possible grip and most comfortable feel.
Fork Cover The Guvnors Brass
CB12088M
/ RS0
€114.94*
Motone The Guvnors solid brass clevis cover.
Manufactured using the hot forging process and then polished to a high shine, the covers provide a very classy fork finish. Looks particularly good in conjunction with the brass steering head nut from our range (see accessories in this description).
Lizenz support HeckWeck R9T - Short
CB12407
/ RS0
€119.95*
Classicbike-Raisch HeckWeck license plate holder - adjustable short version for all BMW R nineT models.
This holder is the perfect mount for our LED Stripe rear kit. It is simply screwed under the LED bracket and then nestles perfectly in the design of the stripe rear. The especially nice thing about the new Short version is that the license plate sits directly under the LED bracket and not as with almost all other rear from the market a good deal to the rear of the nineT protrudes.The license plate size is 170 x 100mm, which covers any license plate size of any country.
To realize the short license plate holder legally, we had to reach into the bag of tricks a bit. Due to the short rear end of the R9T motorcycles, it is not possible to construct a license plate holder that keeps the specified 30° angle and at the same time ensures that the license plate does not come into contact with the rear wheel when the motorcycle compresses really strongly. So we came up with an ingenious adjustment for the license plate that makes it possible to adjust the angle of the license plate.This allows the license plate to be set a little steeper in continuous operation, which of course also looks more awesome. For the TÜV visit or a traffic control is a seconds quick grip with some force on the license plate and everything is legal. See picture 2 & 3.The supplied stop nuts ensure that the license plate can not inadvertently adjust while driving.
In addition, the holder can be used as a universal holder for custom conversions.
The license plate holder is supplied with a LED license plate light (with E-number).
Motogadget Mo.Blaze Tens 1 & 4 Indicator
CB12070.2M
/ RS0
€59.00*
The new Motogadget mo.blaze tens1 & 4 are currently the smallest road legal turn signals in the world. Due to the cleverly chosen design, the turn signals look chic and like a real turn signal despite their tiny size. Thus, they look really good on almost every motorcycle or, depending on their position, they stand out as good as not at all.Particularly advantageous with these turn signals is that they have an M8 thread despite their small size, which makes it possible to mount the turn signal on just about any bracket, adapter & tail from our range.
Its tiny dimensions and reduced design make it almost disappear on the vehicle. As soon as it lights up, it is extremely bright due to the IntensiLED® Technology and definitely no longer to be overlooked. At the same time, the additional lateral beam angle ensures the best visibility and safety. The mounted turn signal has ECE approval as a front and rear direction blinker. The aluminum housing is CNC milled and available in black anodized or mirror polished finish. In addition, the turn signal is optionally available as a normal turn signal and as a version with position light. The turn signals with position light are ONLY suitable for the front. These shine permanently white and ensure that you are better seen when driving behind.
The price is for ONE turn signal and these are sold individually. So please order 2 if a pair is needed.
Specifications:
Total length with thread
29 mm
Leangth without thread
11 mm
Largest diameter
11 mm
Wire leangth
ca. 110 cm
Weigth with wire
ca. 20 g
Mounting
M8 Gewindebolzen
Power consumption
ca. 1 Watt
Motogadget Mo.Blaze Tens 3 Indicator/Rearlight
CB12071.1M
/ RS0
€99.00*
The new Motogadget mo.blaze tens3 are currently the smallest street legal 3-1 turn signal / tail light combination turn signals in the world. 3-1 means that these turn signals combine tail light, brake light as well as turn signals in one housing and that legally.Due to the cleverly chosen design, the turn signals look chic and like a real turn signal despite their tiny size. Thus, they look really good on almost every motorcycle or, depending on their position, they are as good as not at all.Particularly advantageous with these turn signals is that they have an M8 thread despite their small size, which makes it possible to mount the turn signal on just about any bracket, adapter & tail from our range.
Its tiny dimensions and reduced design make it almost disappear on the vehicle. As soon as it lights up, it is extremely bright due to the IntensiLED® Technology and definitely no longer to be overlooked. At the same time, the additional lateral beam angle ensures the best visibility and safety. The mounted turn signal has ECE approval as a front and rear direction blinker. The aluminum housing is CNC machined and available in black anodized or mirror polished finish.
The price is for ONE turn signal and these are sold individually. So please order 2 if a pair is needed.
Specifications:
Total length with thread
29 mm
Leangth without thread
11 mm
Largest diameter
11 mm
Wire leangth
ca. 110 cm
Weigth with wire
ca. 20 g
Mounting
M8 Gewindebolzen
Power consumption
ca. 1/2/3 Watt
Motogadget Mo.Blaze Tens 2 Taillight
CB12073.1M
/ RS0
€59.00*
The mo.blaze tens2 from motogadget is the smallest taillight/brake light combination in the world.
Its tiny dimensions and reduced design make it almost disappear on the vehicle. As soon as it lights up, it is extremely bright due to IntensiLED® Technology and definitely not to be overlooked.
At the same time, the additional lateral beam angle ensures the best visibility and safety.
The taillight / brake light combination has an ECE approval as a rear taillight and brake light. The aluminum housing is CNC machined and available in black anodized or mirror polished finish.
The taillight / brake light combination can be operated like any standard LED light with 12 V.
The price is for ONE turn signal and these are sold individually. So please order 2 if a pair is needed.
Specifications:
Total length with thread
29 mm
Leangth without thread
11 mm
Largest diameter
11 mm
Wire leangth
ca. 110 cm
Weigth with wire
ca. 20 g
Mounting
M8 Gewindebolzen
Power consumption
ca. 1/1 Watt
Rubber bellows clutch cable
CB12067
/ RS0
€19.95*
Rubber bellows for the clutch cable of all air-cooled AC models.
The rubber is left extra a piece longer so that you can cut it to length as needed. Depending on whether and what a AUsrückhebel is installed.
Portmonaie Old Boy
CB12066.1M
/ RS0
€54.95*
The leather wallet is handmade in the traditional way, without compromise from the first cut to the last seam. It has no cheap synthetics, fabric, rubber or inserts.
Made from high quality vegetable tanned leather that will last a lifetime and get better with age.
Also included in the package is a removable leather strap. With this, you can be sure it won't fall out of your pocket while driving or get your wallet pulled out of your pocket in the city.
Details:
Main compartment for money and bills3 card slots2 side pockets for the remaining cardsCoin pocket
Wallet "Moto"
CB12281M
/ RS0
€49.95*
Handmade wild leather wallet "Moto" is a very beautiful and slim wallet.
Made from high quality vegetable tanned leather that will last a lifetime and get better with age.
Included with the wallet is a removable black coated chain. With this, you can be sure it won't fall out of your pocket while driving or get your wallet pulled out of your pocket in the city.
Details:
1 main compartment to hold cash3 card slots1 side pocket for the rest of the cardslength of the chain: 17,5 cmdimensions: 10 x 8,5 cm (closed), 10 x 17 cm (opened)
Front Number Plate Bonneville T100
CB12007
/ RS0
€69.95*
The classic among the license plates is back in our assortment.
The Numbern Plate is simply screwed onto the original fender of the Triumph Bonneville T100. Holder and mounting material are included.
An absolute must on every classic conversion with original long fender!
The plate as well as the brackets are delivered in black powder coated. Optimally suitable to stick numbers, stickers or similar on the sign. The best looks of course an airbrush (see example photo with our Raisch logo).
Included in delivery are the silver stainless steel and the brass cap nuts (see photos).
SP Connect Handy Sleeve universal
CB11992M
/ RS0
€29.99*
With the SP Connect UNIVERSAL PHONE CASE you can use almost any Smartphone (maximum phone size see at the bottom of the description) on any SP Connect cell phone cradle from our program.
The perfect universal case for almost any cell phone. No need to buy an expensive, model-specific case for your cell phone, which has to be bought new every time you change your phone.Simply slide the cell phone into the case, roll up the opening and fix it with the velcro surface. This way, your cell phone is protected from rain, sweat, mud and dust while maintaining touchscreen operability. The fleece slip-on insert and the adhesive EVA frame allow you to find the perfect position for your smartphone.The small, inconspicuous SP Connect cell phone holder (must be purchased separately) stays permanently on your bike and when needed, the cell phone is inserted into the case and mounted to the holder in one easy step. This saves you the purchase of an expensive motorcycle navigation system.
Integrated mounting mechanismProtection against rain, sweat, mud and dustTouchscreen operability remains possibleWindow for cameraScratch-free fleece insertReflective security printing
You can find suitable brackets for the motorcycle in the accessories of this product description.
SP Connect handlebar mount Pro
CB11994M
/ RS0
€69.95*
The SP Connect handlebar mount is simply clamped around your handlebars (mounting is done within a few minutes, the handlebars do not have to be disassembled).Then you can attach any SP Conncet Handy Sleeve (e.g. the universal sleeve from our assortment) to the holder with a single movement. Faster, easier and cheaper you can not get a navigation system to your bike.
CNC manufactured from aircraft aluminum
Landscape or portrait mounting
Super stable 360° adjustment in 6° steps
Suitable for standard and oversize handlebars (2.22 / 2.54 / 2.86 / 3.17 cm // or 0.875 / 1.0 / 1.125 / 1.25 inch diameter)
Note: If you are using a smartphone with a mechanical image stabilizer (all modern cell phones have them), we recommend using the additional anti-vibration module (see accessories in this description) to best prevent possible damage to your phone's camera caused by vibrations from motorcycle engines.
The perfect universal cell phone cover for this mount can be found in the accessories of this description.
SP Conncet Clutch / Brake fitting Mounting Pro
CB11995M
/ RS0
€69.95*
The SP Connect clutch/brake fitting bracket is simply attached to the clamp of your clutch or brake fitting. Suitable screws for mounting are included in delivery.Each SP Conncet Handy sleeve (e.g. the universal sleeve from our range) can be attached to the bracket with a single hand movement. Faster, easier and cheaper you can not get a navigation system to your motorcycle.
CNC milled from aluminium
Pivoting and rotating head for perfect alignmentHigh / landscape format
OptionStainless steel screws
Note: If you are using a smartphone with a mechanical image stabilizer (all modern cell phones have them), we recommend using the additional anti-vibration module (see accessories in this description) to best prevent possible damage to your phone's camera caused by vibrations from motorcycle engines.
The perfect universal cell phone cover for this mount can be found in the accessories of this description.
SP Conncet mirror mount Pro
CB11996
/ RS0
€49.95*
The SP Connect mirror mount is easily and quickly clamped around the arm of your mirror (see below for possible mirror arm diameters).
You can then attach any SP Conncet cell phone cover (e.g. the universal cover from our range) to the holder with one simple movement. Faster, easier and cheaper you can not get a navigation system to your motorcycle.
Partly CNC milled aluminum
Pivoting and rotating head for perfect alignment
Landscape or portrait mounting
Super stable 360° adjustment in 6° steps
Suitable for the following mirror diameters: 10 - 16 mm or 0.39 - 0.63 inch
Note: If you are using a smartphone with a mechanical image stabilizer (all modern cell phones have them), we recommend using the additional anti-vibration module (see accessories in this description) to best prevent possible damage to your phone's camera caused by vibrations from motorcycle engines.
The perfect universal cell phone cover for this mount can be found in the accessories of this description.
SP Conncet handlebar clamp bracket Pro
CB11997
/ RS0
€79.95*
The SP Connect handlebar clamp bracket is mounted on the handlebar clamp of your bike.The delivery includes 3 screws for mounting: M8 screws in three different lengths: 40/45/50 mm
Each SP Conncet cell phone cover (e.g. the universal cover from our product range) can be attached to the holder with a single hand movement. Faster, easier and cheaper you can not get a navigation system to your motorcycle
CNC milled from aluminiumPivoting and rotating head for perfect alignmentportrait / landscape optionStainless steel screwsNote: If you are using a smartphone with a mechanical image stabilizer (all modern cell phones have them), we recommend using the additional anti-vibration module (see accessories in this description) to best prevent possible damage to your phone's camera caused by vibrations from motorcycle engines.
The perfect universal cell phone cover for this mount can be found in the accessories of this description.
SP Conncet handlebar clamp bracket Pro
CB11998
/ RS0
€69.95*
The SP Connect steering head bracket is inserted into the steering head from above and clamped tightly with an expansion plug. For this it is of course necessary that your motorcycle has an open steering head nut. Perfectly suitable for motorcycles with stub handlebars.The delivery includes different expansion plugs to cover all dimensions (dimensions see below).
Every SP Conncet cell phone cover (e.g. the universal cover from our assortment) can be attached to the holder with a single hand movement. Faster, easier and cheaper you can not get a navigation system to your motorcycle
For Supersport motorcycles (stub handlebars)
CNC-machined from aircraft aluminum
Vibration damping
Portrait / landscape option
Stainless steel hardware
For diameters 12-30mm: 12-15mm, 15-18mm, 18-21mm, 21-24mm, 24-27mm, 27-30mm
Note: If you are using a smartphone with a mechanical image stabilizer (all modern cell phones have them), we recommend using the additional anti-vibration module (see accessories in this description) to best prevent possible damage to your phone's camera caused by vibrations from motorcycle engines.
The perfect universal cell phone cover for this mount can be found in the accessories of this description.
SP Connect universal mount
CB11999
/ RS0
€29.95*
With the Velcro fastener, the SP Connect™ Universal Mount can be attached to rods or tubes with a diameter between 20 and 90mm (0.9 - 3.5 inches). The spring-loaded head allows a tool-free 360° rotation of the attached device. The practical thing about this mount is that it can be quickly attached and detached from the motorcycle. In addition, it is also universal and can be used for many other things.Your smartphone can be securely attached to a bicycle, motorcycle, golf cart or stroller so you can use apps, access playlists, read messages or navigate.
Every SP Conncet cell phone case (e.g. the universal case from our product range) can be attached to the cradle with a single hand movement. Faster, easier and cheaper you can't get a navigation system on your motorcycle
Assembly and adjustment without tools
360° adjustment / 45° step size
For diameters from 20-90mm (0.9-3.5 inches)
2 different velcro lengths
Note: If you are using a smartphone with a mechanical image stabilizer (all modern cell phones have them), we recommend using the additional anti-vibration module (see accessories in this description) to best prevent possible damage to your phone's camera caused by vibrations from motorcycle engines.
The perfect universal cell phone cover for this mount can be found in the accessories of this description.
Anti-Vibrations-Modul SP Conncet
CB12000M
/ RS0
€29.95*
Use the SP Connect ANTI VIBRATION MODULE to further reduce vibrations in different frequency ranges. The development of the new product is a reaction to the complexity of newer smartphone models, whose camera systems consist of increasingly sensitive components. The specially developed elastomer inlay dampens in all directions and thus causes up to 60% less vibrations (e.g.: from the motorcycle engine) to reach your smartphone, which could affect the mechanical image stabilizer of the camera. Your smartphone is protected, but still remains stable and quietly mounted so that you can navigate while driving without any problems.
CNC-machined from aircraft aluminum
3D vibration damping through specially developed elastomer inlay
Landscape or portrait mounting
Super stable 360° adjustment in 6° steps
Suitable for all SP Connect mounts with the standard damping head
Easy DIY assembly