The matching flasher in the set (4 pieces for a pair of turn signals) in order not to cut the original wiring harness. These plugs are crimped onto the cables of the turn signals and can then be easily and quickly plugged on the cable harness side.
A set of blinker plugs with cable, suitable for plugging the accessory indicators directly into the original wiring harness of your Triumph 400.
Simply connect the cable ends to your accessory indicators and you can plug the indicators into the wiring harness like the original plug & play.
To easily connect the open cable ends to your indicators, you can simply order our Japan connector set (see accessories in this description).
Dresser Plates for accessory indicators. Cover the open holes at the Bonneville T100 & T120
Pair of METAL! In black, matching the lamp holders.
Can be used to easily conceal the holes when the direction indicators are mounted in a different place or even when accessories are installed in the original place.
Is needed if you install LED turn signals and do not replace the flasher relay. One set is enough for a pair of turn signals.
These resistors are the universal solution for virtually all vehicles and all LED turn signals, if there is a problem with the flashing frequency (even on models where you can set the frequency in the speedometer).
It is also sufficient if you install a set of resistors (usually offers better for space reasons in the back), although you install 4 LED turn signals on the vehicle.
This cable set fits into the original wiring harness with the plug. The open cable ends only need to be connected with blinkers or rear lights from our program (soldering or crimping). Then just heat the shrink tube, heat it up with the lighter, and the professional electrical connection is ready.
320 Japanese plug set for connecting lighting equipment (e.g. indicators on motorcycles).Many accessory indicators (e.g. all Kellermann / Motogadget) have open cable ends. You can order this universal set to connect these easily with cable sets.
The set consists of 3.5mm Japen plug-in sleeves.- Plug + rubber sleeves- Single female plug + rubber sleeves- Double plug + rubber sleeves
Attention, there are also 3 & 4mm plugs on the market. To connect these to the 3.5mm plugs, simply widen or compress the 3.5 slightly.
The CAN-BUS universal resistor can be set to several different ohm numbers (see list below).Who does not know the problem that the flashing frequency does not fit anymore when converting to LED flashers? The problem hasn't become any easier with the new CAN-BUS systems in most motorcycles. On the one hand we have the problem of the wrong flashing frequency, on the other hand error messages are displayed in the speedometer via the CAN-BUS system, if for example a flasher or the rear light is defective. Such an error is also often displayed incorrectly if new indicators or another rear light are installed. And to solve this problem, there is now the universal resistor, which comes with a detailed manual describing how to calculate the suitable resistor and how to adjust it in the resistor (just watch the video in this description).The following resistance values can be set:150 Ohm / 170 Ohm / 200 Ohm / 240 Ohm / 300 Ohm / 400 Ohm / 600 Ohm / 1200 OhmDimensions:Height = 11mm / Width = 31mm (without brackets) / Width = 46mm (with brackets) / Length = 40mmCable length = 200mm with pinsConnections:Yellow = Input channel 1 (+) / Orange = Output channel 1 (+) / Blue = Input channel 2 (+) / Red = Output channel 2 (+) / Grey = Input ground (-) / Black = Output ground (-)
The Rizoma DBL system is a safety device that activates a flashing brake light to warn vehicles behind an intense and sudden braking. The device is activated when properly mounted on the motorcycle when the vehicle makes a sudden deceleration / emergency stop by flashing the brake light at a frequency of 4 Hz (flickering light as known from cars during an emergency stop). The system only works at speeds of 40 km/h and above.
The DBL-Box can easily be connected to the rear light of the motorcycle or to a combination indicator.The sensor is an acceleration sensor and therefore does not need a connection to the brake hydraulics.
Mit dieserm Adapter kann man ganz einfach, ohne Kabel abzuschneiden und zu löten, das Standlicht eines LED Scheinwerfers an ein Motorrad anschließen, das serienmäßig einen einfachen H4 Scheinwerfer mit Standlichtbirne hat.
Those who have cut the original turn signal cable harness side and want to have everything original again, needs these plugs.
Can also be used as a plug connector for accessory flashers etc. together with our counterpart Item No. CB11072.
This LED parking light bulb produces a very modern, bright white LED light, perfectly matching the Phillips LED bulb we sell.
This makes the headlight light of a simple H4 headlight look much more modern.
In addition to the parking light bulb, we also recommend replacing the main headlight bulb with an LED version. The bulb for the main headlight can be found under accessories in this description.
Note for BMW R nineT motorcycles:An additional resistor is required to install the LED bulb on an R9T and not have an error displayed in the speedometer (this can be found under accessories in this product description).
This parking light bulb produces a modern white, slightly bluish light.
Thus the headlight light of a simple H4 headlight appears clearly modern.
Looks especially good in combination with the Night Breakt bulb on the air-cooled Triumph models.
€7.95*
This website uses cookies to ensure the best experience possible. More information...
Shop Relaunch
Hallo lieber Biker,
wir haben vor kurzem auf ein neues Shopsystem umgestellt.
Aller Anfang ist schwer und bringt manchmal kleine Probleme mit sich.
Sollte beim Bestellvorgang etwas nicht funktionieren, lass es uns bitte wissen, wir helfen dir gerne weiter!
Classicbike-Raisch Team
Dear biker,
We recently migrated to a new shop system.
Every beginning is difficult and sometimes brings minor problems with it.
If something doesn't work during the order process, please let us know and we'll be happy to help!