Please choose your bike
Flat Seat Hump - R12 nineT
CB12855
/ RS
€239.00*
Seat cover / hump in flat style look for the original seat of the BMW R12 nineT
Coming soon! Contact us if you want to be informed as soon as the part is available. The currently stated price is not yet the final price.
The R12 really cries out for a flat hump at the rear. We have made it our mission to develop a perfect solution here. The flat hump integrates perfectly into the original rear, seat and rear light of the nineT. The rear end looks particularly good in combination with our rear eliminator kit. The hump is attached completely without visible screws.
Frame plate BMW R12
CB12805
/ RS
€69.90*
BMW R12 The Line Frame Plates Set.
These beautiful plates, milled from aluminium and with a discreet bmw logo, replace the original plastic emblems on the frame of your BMW R12 / R12 nineT.
The Line emblems are anodised in black and then a very fine milling head is used to mill the The Line design, which is then discreetly visible in silver.
Matching tank emblems are also available for the BMW in the same design (see accessories in this product description).
The set consists of one plate for the left and one for the right side.
Tip
Rear Eliminator Kit - R12 nineT
CB12808
/ RS-10
€159.95*
Rear conversion kit / mudguard eliminator kit for BMW R12 nineT
Made in Germany by Classicbike-Raisch
Give your BMW R12 nineT a modern and minimalist design with our rear conversion kit, which has been developed legally and in accordance with legal requirements. Depending on the choice of licence plate holder, TÜV registration may be required.
This kit ensures a significantly shorter, tidier rear end and replaces the original, long plastic licence plate holder. The result: a harmonious, clean motorbike design with a flat, sporty line.ATTENTION FOR MODELS WITHOUT A CENTRAL TAIL LIGHT.In some markets, the R12 is supplied without a central tail light (these have the tail light integrated into the indicators).For these models, you must order a separate 3-1 indicator/rear light combination from our shop instead of the indicators shown here.
Scope of delivery
The kit contains everything you need to convert the rear as shown in the pictures:
Aluminium rear lower shell: Black powder-coated, for a straight, flat rear line. It also acts as a splash guard and provides space for electronic components under the seat.
Black powder-coated indicator holder: Suitable for all accessory indicators with M8 thread.(Note: Original indicators cannot be used. M5 to M8 adapters are required for Kellermann Atto indicators).
3D-printed brackets: For securely fastening fuses and plugs under the seat.
Mounting materials: Including rubber sleeves for neat cable routing.
Installation instructions: For simple plug & play installation.
Necessary accessories
To fully utilise the kit, you will need the following components:
Indicator
The original indicators are not compatible. Accessory indicators with M8 thread must be fitted. Suitable models can be ordered as a set directly under the product description(incl. 10 % discount).
Recommendations:
Motogadget Pin / Tens
Motone Pico
Kellermann Atto (M5 to M8 adapter required)
Rizoma Club / Leggera
Side licence plate holder
The original licence plate holder is removed. A side licence plate holder is required and can also be ordered directly as a set with a discount. You have a choice of four variants:
Raisch Vario holder: Minimalist, inexpensive and variably adjustable, suitable for all licence plate sizes.(Requires individual approval by the TÜV).
Rizoma holder: High-quality option with parts certificate, no TÜV registration required.
Adjustable holder: With aluminium number plate and variable adjustment.(Requires individual TÜV approval.)
AC-Schnitzer bracket: CNC-milled with parts certificate.
Optional accessories
Complete your conversion kit with these practical extras (all of which you can also add to the kit below the description)
Indicatorplug: Makes it easier to wire the accessory indicators to the original wiring harness.
Threaded indicator caps: For a clean look over the nuts of the indicators.
Reflector: For 100 % road approval, can be mounted under the licence plate.
Licence plate screws: For secure and aesthetic mounting.
Conversion to
Conclusion
Our rear conversion kit for the BMW R12 nineT transforms your motorbike into a real eye-catcher. Thanks to high-quality materials, simple installation and a wide range of accessories, you can customise your bike and meet the legal requirements at the same time.
LED Stripe Tail Tidy BMW R9T
CB12076M
/ RS-10
€309.00*
Classicbike-Raisch LED Stripe rear suitable for all BMW R nineT models. Street legal!
The LED Stripe rear is the most noble & elegant rear for nineT models that we have in our range.The rear of your nineT is given a minimalist & modern look with this kit, through the filigree milling bracket and the modern LED strip & completely legal! The tail light with breaklight is with E-number and the tail complies with all StvO standards. Here nothing needs to be registered with the TÜV. Simply attach & enjoy.
The LED bracket milled from aluminum fits perfectly to all BMW original seats as well as the BMW hump. A perfect fit on all seat benches is guaranteed by the spacer kit, which is included. This kit contains different spacers to distance the height of the milling bracket perfectly to the respective installed seat. The kit of course also works with numerous seat benches from the accessories, such as the Cool Seat from our range.Also with the passenger pillion frame everything fits perfectly.
The bracket for the LED strip is milled from an aluminum block in Germany and then anodized deep black. The LED strip (with E-number) is then glued into the milling bracket. This makes the part look like it was cast from one piece.
Included in the kit is an aluminum underbody plate, which replaces the original plastic shell. For the R nineT Euro 4 & 5 models, the plastic box for the control unit is also replaced. This is unsightly on the one hand because it is made of plastic and on the other hand because it builds up very low and thus disturbs the line of the rear area. Through the new aluminum sheet you no longer look from the side on the edge of the box & the rear gets a perfect line.
The scope of delivery includes all materials, such as screws, cable ties, heat shrink tubing, connectors, etc., as well as a very detailed step by step instructions to ensure easy & problem-free installation.
To buy the kit reduced in the set, simply below the description, the accessory items such as turn signals, reduced order.
License plate holder: The kit is delivered WITHOUT a license plate holder.
Since the kit looks just awesome with both a central and a side license plate holder! Our recommendations:Variant 1: License plate holder HeckWeck R9T / This holder is mounted centrally under the rear and was developed specifically for the LED Stripe rear (StvO compliant does NOT need to be registered). This is the holder, which is also mounted on some product photos.Variant 2: License plate holder HeckWeck R9T - Short / This holder is mounted as in variant 1 centrally under the rear and was developed specifically for the LED Stripe rear (StvO compliant must NOT be registered). The difference to variant 1 is that the short version is much shorter and has an adjustment for the angle of the license plate. This allows us to mount the license plate significantly shorter (steeper than 30 °) but for TÜV or controls within a handle to be able to put down to 30°.
Variant 3 Side license plate holder:There are 4 different holders to choose from: 1. the Vario holder: an inexpensive (but still very high quality) holder reduced to the bare essentials (the most inconspicuous of all), which fits all license plate sizes and is variably adjustable in position - must be registered individually.2. the Rizoma holder: Probably the highest quality holder of all. This holder is supplied with a parts certificate and can simply be fitted (does not have to be registered with the TÜV).3. the adjustable bracket: A sophisticated bracket with an aluminum license plate, which also has variable adjustment. Must also be registered by individual approval. 4. The AC-Schnitzer holder: A license plate holder milled from solid material with parts certificate.
Turn signal:
In the milling bracket is on both sides a 8er bore, this allows it to mount any turn signal with an M8 thread. He is held turn signal by a grub screw, which is included.Who does not want to mount a turn signal on the bracket, which can order the turn signal plugs (further down in this description). These then serve as blind plugs for the turn signal hole.
Further down in this description you can order all, to the rear matching turn signals, from our range in the bundle. In the bundle you will automatically be granted a discount of 10% on all turn signals.
Accessories:
Classicbike-Raisch recommends for easier installation still turn signal plugs & tail light plugs.For all those who want to be 100% legal on the road, there is still a reflector as an accessory.To mount the license plate, we recommend the license plate screw set.
All parts you can order below in the description with it.
To buy the kit reduced in a set click on the button "buy this item in a set" above under shopping cart
Luggage:The LED bracket goes to the same mounting points as most luggage systems. Together with the LED stripe rear, the Unit Garage bags can be mounted.
Note on the BMW alarm system: Our base plate does not have any fixing points for the alarm system. If you would still like to have it installed, we recommend attaching the alarm system with double-sided adhesive tape.
Side license plate holder - Vario R9T
CB12560
/ RS-1
€119.95*
The side Classicbike-Raisch Vario license plate holder for all BMW R nineT models has a sophisticated mounting system, which makes it possible that the license plate holder on the one hand looks good and does not protrude too far to the outside and is legal and registrable.
Through various mounting holes, it is possible to set the license plate far to the outside. This then allows a registration with your TÜV inspector of confidence.Side license plate holders do not necessarily need an ABE, to register them they must only comply with the StvO guidelines, which is given with our Vario holder, if the license plate is mounted at the outermost position. After registration, the license plate can then be placed further inwards for a nicer look. The product pictures illustrate the adjustment range of the license plate. Please clarify in advance with your TÜV inspector whether he will register the license plate holder (if necessary, we can provide a sample registration).
The license plate carrier has a dimension of: Height = 100mm / Width = 155mm - The dimension is small enough to accommodate all motorcycle license plates in the world.
Included in delivery:
- Side license plate holder - Mounting material + cable for the license plate light - LED license plate light- Detailed step by step mounting instructions
Classicbike-Raisch Tip: If you want to mount your license plate as unobtrusively and coherently as possible, we recommend ordering a set of license plate screws (you can find them under the accessories in this description).
R9T Aluminium mudguard - Long
CB11140M
/ RS-1
€229.00*
Aluminum front fender for R9T Scrambler & Urban GS in the long version.There is also a short version (see similar articles in this description).
This handmade aluminum fender is extra nice slim chosen by us. He is extra slightly narrower than the front tire, which ensures that the tire looks wider. An optimal splash protection is still given. In the long version, the fender is particularly longer in the rear part and thus looks more classic.
The fender is supplied as a kit, including a holder (which is original from BMW) and mounting hardware. This is available in silver or black (selection: color).
The supplied holder / stabilizer is made of sturdy die-cast aluminum. Some other suppliers deliver here only a simple sheet metal stamped part.This has the advantage that the holder also provides stiffening in the fork.
The fender is available in 3 finishes: Polished, brushed (then he has a really nice polish) or black powder coated.
R9T Alu front fender - Short
CB11141M
/ RS-1
€229.00*
Aluminum front fender for R9T Scrambler & Urban GS in the short version.There is also a long version (see similar articles in this description).
This handmade aluminum fender is extra nice slim chosen by us. He is extra slightly narrower than the front tire, which ensures that the tire looks wider. An optimal splash protection is still given. In the short version, the fender is a really nice crisp short fender, which provides a sporty look.
The supplied holder / stabilizer is made of sturdy die-cast aluminum.... Some other suppliers only supply a simple sheet metal stamped part here.This has the advantage that the holder also provides stiffening in the fork.
The fender is available in 3 finishes: Polished, brushed (then he has a really nice grinding pattern) or black powder coated.
Short license plate holder - R12 nineT
CB12698
/ RS0
€109.95*
Short license plate holder for your BMW R12 nineT – style meets functionality
Do you want to upgrade the rear of your BMW R12 nineT without losing much time? Our high-quality, short license plate holder made of aluminum makes it possible – and without much effort.
With this license plate holder, you can give your bike a clean, sporty look in no time. It comes as a plug & play solution, including a discreet, pre-assembled LED license plate light and a suitable vehicle plug. Simply screw it on, connect the plug, and you're done – the whole thing takes no more than 15 minutes and is super easy for anyone to do.
The original plastic holder looks quite cheap in comparison, and the bulky, long license plate light plus the oversized reflector? A real style clash! With our elegant license plate holder, your license plate sits significantly higher and blends harmoniously into the overall look of your motorcycle – for a clean and tidy look from behind.
Our Classicbike-Raisch license plate holder is made of sturdy aluminum and finished in Germany with a high-quality black powder coating. Everything is pre-assembled and wired by hand in-house, so you can be sure that the quality and appearance are right.Turn signals: Do you want to get rid of the original plastic turn signals as part of the rear end conversion of your BMW R nineT and replace them with beautiful turn signals from the accessories? No problem, just order our turn signal adapter (see accessories in this description) and you can simply order and install a set of accessory turn signals from our range.
Classicbike-Raisch tip:
If you want to be completely legal on the road, unfortunately you can't avoid a reflector. But don't worry, we offer you a slim, unobtrusive alternative to the bulky original. You can easily find it under “Accessories” in this product description.
For the perfect attachment of your license plate, we recommend that you order a set of license plate screws at the same time.
If you are also replacing the turn signals, order the turn signal plugs at the same time, so that the new turn signals can simply be plugged in.
Make your life easier and your bike more beautiful – with our short license plate holder for the BMW R12 nineT!
BMW Tankemblem - The Line
CB12685
/ RS0
€24.95*
This BMW tank emblem milled from aluminum is just the thing for all BMW drivers who like it black and beautifully simple! The subtly suggested BMW propeller and the finely milled BMW lettering look very elegant.
Attention!The emblems are sold individually
The original emblems on the tank are glued on and can be carefully removed.The new black emblems have double-sided adhesive on the back and can therefore be easily attached to the motorcycle.
Classicbike-Raisch tip: We also offer matching brake/clutch reservoir covers in "The Line" design. These can be found under accessories for this product.
The emblems are available separately.
Diameter tank emblem: 70mm
BMW Milled - Black Emblem
CB12582.1M
/ RS0
€17.95*
This BMW tank & seat hump emblem milled from aluminum is just right for all BMW riders who like it black true to the motto Black is beautiful.
The original emblems on the tank and on the hump are glued and can be carefully removed.The new black emblems have a double-sided adhesive on the back, which makes them very easy to attach to the motorcycle.
The emblems are sold individually.
Diameter tank emblem: 70mm / Diameter hump emblem: 26mm
Kotflügel High R9T
CB12574M
/ RS0
€259.95*
Top-mounted aluminum mudguard for BMW R nineT models.
This top-mounted mudguard gives your R9T a real off-road MX look. Because a proper scrambler / off-road machine simply needs a high-mounted mudguard.
The mudguard is made of aluminum and is available in either black coated or brushed silver (the brushed version has a transparent protective coating).
Note Urban GS:To install the mudguard on an Urban GS, the original lamp cover must be removed. In addition, a new lamp holder is supplied in the kit for the Urban GS, which means that the lamp then sits in the same position as on a Scrambler.
Aluminum front mudguard - BMW
CB12575M
/ RS0
€339.95*
This Unit Garage aluminum front fender suitable for BMW R nineT Classic & BMW R12 models is supplied including bracket.
The short aluminum mudguard and the beautiful bracket made of round steel fits perfectly to the classic design of the nineT Classic. The bracket also serves as protection for the fork tubes.
The mudguard is made of aluminum and is available in either black coated or brushed silver (the brushed version has a transparent protective coating).
HeckWeck Tail Kit R9T - Short
CB12531M
/ RS0
€209.95*
Classicbike-Raisch HeckWeck Kit SHORT version made in Germany, suitable for all BMW R nineT models. Street legal.
All our HeckWeck Kits are very minimalistic rear ends, which make for a really free and clean rear end. Our HeckWeck kits are designed to be fitted with 3-1 turn signals. This means that the turn signals, tail light, brake light and indicator are integrated at the same time. For mounting the turn signals, an indicator holder is included, which sits on the number plate. This is variably adjustable in width in order to have the perfect dimension depending on the width of the number plate and the turn signals.
Matching 3-1 turn signals can be ordered as a set below the description with a 10% discount.
In order to be able to legally realise the short number plate holder, we had to reach into the bag of tricks a little. Due to the short rear end of the R9T motorbikes, it is not possible to construct a licence plate holder that adheres to the specified 30° angle and at the same time ensures that the licence plate does not make contact with the rear wheel when the motorbike compresses really hard. So we came up with an ingenious adjustment for the number plate that makes it possible to adjust the angle of the number plate.This allows the number plate to be set a little steeper in continuous operation, which of course also looks more attractive. For the TÜV visit or a traffic control, a quick grip with a little force on the number plate is enough and everything is legal. See pictures 2 & 3.The stop nuts supplied with the kit ensure that the number plate cannot be moved unintentionally while driving.
Included in the kit is an aluminium underbody plate, which replaces the original plastic shell. For the R nineT Euro 4 & 5 models, the plastic box for the control unit is also replaced. This is unsightly on the one hand because it is made of plastic and on the other hand because it is very low and therefore disturbs the line of the rear area. With the new aluminium sheet you don't have to look at the edge of the box from the side anymore & the rear gets a perfect line.
Accessories:
Classicbike-Raisch recommends the "R9T cable set for tail light/indicator combination" for easier installation. This allows you to easily connect the 3-1 turn signals without having to cut anything off the wiring harness.
For all those who want to be 100% legal on the road, there is also a reflector in the accessories.
To mount the number plate, we recommend the number plate screw set.
All parts can be ordered as a set below the description.
Scope of delivery:
Licence plate holder (suitable small size for all motorbike licence plates in the world)
LED number plate light
Indicator holder vario (the width can be adjusted individually depending on the number plate and indicator length)
All mounting materials
Accessories mounting material such as heat shrink tubing, cable ties etc.
Detailed assembly instructions
Fork Caps - BMW Milled
CB12457M
/ RS0
€89.95*
A pair of CNC machined aluminum caps for all BMW R nineT models with Tele fork. Matching our BMW Milled series, there are now also the fork crown caps. These replace the rather simple silver caps on the R9T fork.
The caps are easily replaced within a few minutes against the original. To install the fork does not have to be removed (it must only be relieved, for example, in which the motorcycle is jacked up, or pulled by a second man on the side stand) and no special tools are needed. An assembly instruction is included in the delivery,
The Milled caps are manufactured in a very noble Black Pearl surface. That is, they are blasted before the black anodize, Glasperenl. This gives its very fine, slightly matte surface which feels and looks very high quality.
Classicbike-Raisch recommendation: Order the plastic tool as well, with which it is very easy to fit the Milled caps without scratches and scratches (see accessory article in this description).
Steering head nut cover CNC Milled
CB12370.2M
/ RS0
€59.95*
CNC machined aluminum cover for the steering head nut of all BMW R nineT models.
The original Lemkkopf nut of the R9T's is not exactly beautiful. To replace this is quite costly, because the handlebars must be disassembled for this. So we offer you here a very chic and practical cover. It is simply plugged over the steering head nut and covers this completely. The cover is put on it within seconds or pulled off again.
The Milled design of the steering head cover is the same as our other Milled Producten (tank emblems, brake reservoir cover ...)
Radiator grille - R9T / R12
CB12388
/ RS0
€79.95*
Classicbike-Raisch aluminum protective grille for the oil cooler of all BMW R nineT & R12 models.Made in Germany!
The protective grille serves two purposes.First and foremost, it protects the radiator from rough stone chips, which is especially important if you are also a bit off road.In addition, the grille also looks visually nicer, and hints at the BMW logo.Due to the many slots, sufficient cooling is guaranteed.
The grid is made of aluminum and is laser cut and edged by hand in our region. Subsequently, the Gitte is coated black powder.
%
Fork Covers with Indicators R9T
CB12096M
/ RS0
€179.95*
A pair of aluminium standpipe covers with integrated LED turn signals for BMW R nineT.
These very high-quality fork covers ensure that the mismatching chrome on the fork disappears and that the fork appears thicker (like an upside down fork). In addition, tiny LED turn signals are integrated into the covers. This does away with the large original turn signals and gives the nineT a really nice clean front.The turn signals are E-numbered and also comply with the prescribed minimum distance (so they are Stvo compliant and legal).
The tubes are elaborately turned on a CNC lathe, have guides for the cables and rubber rings milled into them from the inside. On the outside they have a small flat surface on which the mini LED turn signals are mounted.After that, the covers are glass bead blasted and then anodised either silver or black. This gives the covers a very high-quality matt finish.
The covers are supplied with detailed step-by-step assembly instructions, cable solder connectors, heat shrink tubing and resistors (which are required for some models)
Note Scrambler / Urban GS cover:The indicators on these covers are now mounted horizontally to make them even more inconspicuous.
License support HeckWeck R9T
CB12074
/ RS0
€99.95*
Classicbike-Raisch HeckWeck license plate holder for all BMW R nineT models.
This holder is the perfect mount for our LED Stripe rear kit. It is simply screwed under the LED bracket and then nestles perfectly in the design of the stripe rear. Perfect for all you want to drive one of our LED Stripe rear and do not want to have a side license plate holder.
Also, the holder can be used as a universal holder for custom conversions.
We have designed the holder so that it ensures a safe ride in all driving situations as well as in 2-man operation and the license plate can not pull into the rear wheel.The license plate holder is Stvo compliant and street legal.
The license plate holder is supplied with a LED license plate light (with E-number).
HeckWeck Tail Kit R9T
CB12352M
/ RS0
€189.95*
Classicbike-Raisch HeckWeck Kit made in Germany, suitable for all BMW R nineT models. Street legal! All of our HeckWeck Kits are very minimalistic rear ends that make for a really free and clean rear end. Our HeckWeck kits are designed to have 3-1 turn signals. This means that in the turn signals, rear, brake & turn signal light are integrated simultaneously. For mounting the turn signals, a turn signal holder is included, which sits with the license plate.
Matching 3-1 turn signals, you can order below the description with 10% discount in the set equal to it.
Included in the kit is an aluminum underbody plate, which replaces the original plastic shell. For the R nineT Euro 4 & 5 models, the plastic box for the control unit is also replaced. This is unsightly on the one hand because it is made of plastic and on the other hand because it builds up very low and thus disturbs the line of the rear area. Through the new aluminum sheet you no longer look from the side on the edge of the box & the rear gets a perfect line.
Accessories:
Classicbike-Raisch recommends the "cable set R9T for taillight / turn signal combination" for easier installation. This allows you to easily connect the 3-1 turn signals without having to cut what on the wiring harness.
For all those who want to be 100% legal on the road, there is still a reflector in the accessories.
To mount the license plate chic, we recommend the license plate screw set.
All parts you can order below the description, in the set with it.
Scope of delivery:
License plate holder (165mm x 135mm)
LED license plate lighting
Turn signal holder
All mounting materials
Accessories mounting material such as heat shrink tubing, cable ties, etc.
Detailed mounting instructions
Lizenz support HeckWeck R9T - Short
CB12407
/ RS0
€119.95*
Classicbike-Raisch HeckWeck license plate holder - adjustable short version for all BMW R nineT models.
This holder is the perfect mount for our LED Stripe rear kit. It is simply screwed under the LED bracket and then nestles perfectly in the design of the stripe rear. The especially nice thing about the new Short version is that the license plate sits directly under the LED bracket and not as with almost all other rear from the market a good deal to the rear of the nineT protrudes.The license plate size is 170 x 100mm, which covers any license plate size of any country.
To realize the short license plate holder legally, we had to reach into the bag of tricks a bit. Due to the short rear end of the R9T motorcycles, it is not possible to construct a license plate holder that keeps the specified 30° angle and at the same time ensures that the license plate does not come into contact with the rear wheel when the motorcycle compresses really strongly. So we came up with an ingenious adjustment for the license plate that makes it possible to adjust the angle of the license plate.This allows the license plate to be set a little steeper in continuous operation, which of course also looks more awesome. For the TÜV visit or a traffic control is a seconds quick grip with some force on the license plate and everything is legal. See picture 2 & 3.The supplied stop nuts ensure that the license plate can not inadvertently adjust while driving.
In addition, the holder can be used as a universal holder for custom conversions.
The license plate holder is supplied with a LED license plate light (with E-number).
Foot rest R9T black powder coating
CB11967
/ RS0
€130.00*
Also the footrest support plate and the heel guard, like most metal parts on the R9T's, have the unsightly die-cast surface, which does not look very noble. But we can also powder coat them black!
Attention! With this article you order ONLY order the SERVICE that we powder coat your original parts. So you have to send us your parts and we will send them back after we powder coated them in black.
Many would like to have a black footrest. The first consideration would be a completely new detent system, e.g. from LSL or Rizoma, which is clearly the most beautiful solution. But if that is too expensive for you, you can get a cheap alternative by having the carrier plate and the heel protection coated in black, ordering black detents and a black gearshift (you can find suitable articles under the accessories products in this description).
You just send us your two footrest support plates + heel guard right, we sandblast them, stick all parts that have to remain free and coat them black (RAL9005)
The brake light switch is attached to the detent carrier plate with 2 notched nails ex works. These must be drilled out for coating and then hammered in again (you can order new notched nails with the switch, see accessories in this description). If you do not want to do this work yourself, you can order the article "Drill / hammer in notched nails R9T carrier plate" (see accessories in this description).
Duration until you have your part black coated again: approx. 2 - 3 weeks.
Sidecover / Airbox Cover R9T Flat Style
CB11970M
/ RS0
€64.95*
Aluminium Flat Style side cover for all BMW R nine T models.These side lids are placed in the free frame triangles of the nineT and cover the ugly plastic air box. They fit perfectly to the frame shape and look like they belong to the original bike.The slots in the lids make the parts an eye-catcher.Without such lids or a bag, the R9T area looks a bit cheap, because you have a clear view of the plastic box (a nice thing when riding open K&N filters, but not when looking at an air box).The covers are fixed with plastic clamps (black) that are clamped around the frame. Screws, clamps, a detailed step by step assembly instruction and everything else needed for the assembly is included.Available for left or right and as a set.
Frame batch BMW R nine T
CB11971M
/ RS0
€24.95*
Aluminium frame batch with nineT or R-Logo lettering for the passenger frame on all BMW R nine T models.
Many people drive their R9T without pillion frame and have the two threads open on the right & left side.Therefore we designed two nice badges which are mounted on this place.Matching black screws are including.
Foot rest R9T black powder coating
CB12112
/ RS0
€45.00*
The gear levers, like most metal parts on the R9T's, have the unattractive die-cast surface, which doesn't look very classy. But we can also coat them with black powder!
Attention! With this article you order ONLY order the SERVICE that we powder coat your original parts. So you have to send us your parts and we will send them back after we powder coated them in black.
Together with the black coating of your R9T's footrest system (see accessories article in this description), you get a completely black footrest system.
You simply send us your gear lever, we sandblast it, tape all the places that have to remain free and coat it black (RAL9005).
Duration until you have your part coated black again: approx. 2 - 3 weeks.
Side Mount Lizenz support R9T
CB11929M
/ RS0
€199.00*
Three-part license plate holder made of 3mm aluminium or stainless steel for all BMW R nineT models, from our friendly company KRT Framework.As well as all parts, which come from KRT, also the lateral license plate holder is of the highest quality and absolutely perfectly designed.The delivery includes all mounting materials and a license plate light.The two aluminium support plates allow an assembly where screws and cables disappear. Long holes paired with three different hole patterns allow the assembly in your desired position (side and height is adjustable).There is the license plate holder with different plates for the countries (Germany, Austria, Switzerland, France, Holland, Belgium. Please choose in the selection).Dimensions of the license plates for the different countries:
Germany: 180 x 200 mmSwitzerland: 180 x 140 mmAustria: 210 x 170 mmFrance: 210 x 130 mmNetherlands: 210 x 140 mmBelgium: 210 x 140 mmItaly: 177x177 mmSpain: 220x160 mmUSA: 178x102 mm
Side Cover Leather Bags BMW R9T
CB11904M
/ RS0
€169.95*
Vintage genuine leather side covers that also act as a small bag, suitable for all BMW R nine T models.
The open frames of the R nine T's are not very nice, because you just have to look at the plastic air box. That's why we thought that it could be made nicer.So we came up with something in cooperation with a small Italian leather company. Leather side lids which are also a little thing for small things like purse, mobile phone, tools etc. What is better than an optically chic part, which is also very practical.
The handmade bags are available in a choice of vintage brown or black. The bag is fastened to the frame of the bike with three leather straps (included). Very high-quality and thick cowhide leather is used, so that the bags last a lifetime. With time the leather gets a really nice patina and the bags become even more beautiful.
The price is for one side (please choose in the selection if you want the bag for left or right).
Intake Cover Kit BMW R9T
CB11888M
/ RS0
€359.00*
The original and long intake snorkel of the BMW R nine T models belongs classically to the R9T, but by far not everyone likes it! On some machines it even looks like a foreign body and does not fit nicely to the shape of the tank.So our good friend Marvin from KRT Framework thought that it would be a much nicer solution. With the short intake kit there is finally a solution that replaces the much too long intake snorkel with a nice short one that fits more than perfectly to the tank shape of the R9T.
The inner snorkel in the kit ensures that cool ambient air and airflow is still sucked in and not warm ram air from under the tank. The snorkel is made of 2mm thick aluminum sheet metal, TIG welded and black satin powder coated.It is simply exchanged against the original part. There are no adjustments necessary, so your R nineT can be retrofitted at any time.
The corresponding air intake cover is made of carbon fiber using an infusion process, just like it is used in professional motorsports.Afterwards the cover is painted either in black silk matt or the original BMW color of the scrambler "Monolith metallic matt".Furthermore, the cover is still available in raw. This is then only filled and delivered ready to paint. Please choose the desired color in the selection.
The cover will be fixed to the snorkel as well as to the two original screwing points.
The cover integrates perfectly into the tank shape and makes the R nineT look sportier and more compact.
Included in the kit is an air inlet cover made of carbon fiber fabric, the inner snorkel is made of aluminum, as well as all the small material needed for mounting.A material certificate of the carbon fiber cover is also included in the delivery.
BMW R9T JVB Moto Racer Heck
CB11638
/ RS0
€420.00*
GFK Racer Rear suitable for all R9T models gives each R9T a completely new look.We have often been asked if there is a Plug&Play solution to completely change the rear of the R9T. Finally they are here now.The Racer rear is delivered ready to mount, including mounting material and an LED tail light (which is integrated into the rear). The assembly is also relatively simple (see assembly instructions in the downloads of this article description).This rear is made of high quality GFK and is perfect for painting.Not included in the delivery is: the cell rubber seat cushion, a license plate holder (we recommend to use a lateral one to have the nice rear as free as possible), as well as the indicator holder mounted on the photos. But you can find all these things under the accessories in this description.In addition we recommend to order the "adapter plug accessory rear light" for better wiring (also to be found in the accessories).
The JVB Moto rear fits perfectly into the design of all JVB Moto things for the BMW R9T series (air tunnel, lamp mask, R9T Racer fairing, front fender).
BMW R9T Headlight Kit JVB Moto
CB11644M
/ RS0
€349.00*
JVB Moto lamp mask with headlight insert (in 4 different versions) for mounting on the R9T Classic with USD fork. Fits both Euro3 and Euro4 models.
The lamp mask is made of very high quality ABS plastic and is perfect for painting! The mask is delivered complete with all mounting materials and a suitable headlight insert.All 4 headlight versions are of course with E-number.
The lamp mask makes the R9T a completely different motorcycle! A real eye-catcher, if a R9T has no protruding headlight pot. Looks great with a sporty as well as with a radical scrambler conversion. The design of the headlight mask fits perfectly into the complete JVB Moto Bodyparts line (rear, air tunnel & fenders).
Of course the flat lamp mask looks especially good if a small Motogadget speedo (see accessories in this description) is installed (the speedo only works on Euro3 models). In addition the suitable speedo holder is then still needed (accessory).
Note version 4 headlights:This conversion kit is vehicle specific JvB-moto conversion parts and a universal LED headlight insert. The connection of the LED headlight is complicated. It must be individually connected to the existing vehicle electronics. Additional articles for connection, e.g. Art. No. 41356 or additional switches may be necessary. Due to the low power decrease of the LED headlight, it is possible that the bus system of the vehicle declares the lighting as defective and displays it as a fault in the speedometer. Due to changes in the series on the part of the vehicle manufacturer, it is not possible to prevent such an error message from the outset by an appropriate scope of supply and offer a solution in any case.If you have any doubts with regard to the installation, please contact an authorized dealer before installation and ask for advice with regard to expected problems.
K&N dummy air filter kit
CB11611
/ RS0
€174.95*
K&N dummy air filter pair BMW R nineT
For the look as if you had installed open single air filters, but 100% legal. Fits all R9T models. As the original K&N air filters are unfortunately not exactly cheap (they alone cost over 130 EUR), the price is quite high.
We have now been asked very often whether it would be possible to fit attractive K&N single air filters to the R9T for visual reasons. Of course, anything is possible, BUT: 1. it is a huge effort to remove the entire AirBox & 2. it is absolutely illegal. So we thought about making dummies from original K&N air filters, which are then pushed over the original intake hose and fastened with the supplied clamp. To do this, we cut the filters open at the back and neatly seal the cut so that the filters cannot tear any further. An absolute visual highlight on every R9T!
Air filter in black: When new, the K&N filters are purple in colour due to the oil with which they are lubricated . If you don't like this colour, you can also make the filters black with the matching K&N oil (see accessories article in this description).
Fitting the filters is very simple and self-explanatory.
Black Powder coating fork bridges
CB11476
/ RS0
€155.00*
BLACK BLACK BLACK. Like so many parts on the R9Ts, the triple clamps also have the unattractive die-cast surface look, which does not look very classy! So that the triple clamps get a nice & smooth surface in black, we also offer for this the powder coating in black (other colors only on request and with exact RAL tone specification!).
Black are made: upper & lower triple clamp. We also recommend the lamp holder and the steering damper holder to be coated black (both parts can be found under the accessories in this description).
Duration until you get the part back is about 2 - 4 weeks.
Speed rings black coated
CB11478M
/ RS0
€30.00*
Of course, the speedo rings in black should not be missing! Where does the driver look more than the speedometer? And who is on black, of course, must have the rings in black!
Duration until you recover the part is about 1 1/2 - 2 weeks.
By default, we always do the parts in black. Semi-matt several other colors are of course also possible on request (but then the exact RAL tone must be specified).
upper triple clamp R9T Racer black coating
CB11646
/ RS0
€85.00*
BLACK BLACK BLACK. Like so many parts on the R9T models, the upper (visible) triple clamp of the R9T Racer has the ugly die-cast surface look, which doesn't look very noble! So that the triple clamps get a nice & smooth surface in black, we also offer powder coating in black. (other colours only on request and with exact RAL tone!)
Attention! With this article you order ONLY order the SERVICE that we powder coat your original parts. So you have to send us your parts and we will send them back after we powder coated them in black.It will take about 1 1/2 - 2 weeks until the part is finished.
Handlebar mount black coated - R9T
CB12599
/ RS0
€90.00*
Black complacent?
If you want to pull a black line on your R9T, you should also be able to coat the original signals with a nice handlebar mount black. Actually, because: here, too, we have the ugly die-cast look that hardly anyone likes. Very effective both as a contrast with the original silver handlebar and together with a black handlebar!
Attention! With this article you order ONLY order the SERVICE that we powder coat your original parts. So you have to send us your parts and we will send them back after we powder coated them in black.
Duration until you recover the part is about 4-6 weeks
By default, we always do the parts in black. Semi-matt several other colors are of course also possible on request (but then the exact RAL tone must be specified).
Screw Set Black R9T
CB11442
/ RS0
€58.90*
A complete stainless steel Torx bolt set with black coated screw heads for BMW R9T. True to the motto "Black is beautiful" almost all visible screws in black are included in the set to replace them with the original ones.
All included screws are A2-70 stainless steel and have been powder coated in a nice black matte. Optically great, if the screws should not attract attention. No chipping off the paint! The screws are neatly packed in bags for the respective engine cover. The exchange is thus very easy. It is exchanged one screw after the other. As a result, no new seals are needed.
The end cover screws are included in this set. The kit includes the screws (cylinder head, as well as Linsenkopf) and needed U-washers for: - front cover - Crankshaft sensor - Oil cooler cover - Oil cooler mounting - Oil cooler line - Oil cooler supply line - Oil cooler line return - starters - intake manifold - Apprentice trainee - Throttle valve switch
Front cover screws Black R9T
CB11443
/ RS0
€34.90*
Stainless steel Torx bolt set for the front cover of the BMW R9T. True to the motto "Black is beautiful" are in the screw set all the screws to replace it with the original silver on the front cover of the R9T.
All screws included (ISO 14579) are A2-70 stainless steel and have been powder coated in a beautiful black matte finish. No chipping off the paint! The screws are neatly packed in bags for the respective engine cover. The exchange is thus very easy. It is exchanged one screw after the other. As a result, no new seals are needed.
Headlight R9T black coating
CB11436
/ RS0
€35.00*
True to the motto "black is beautiful" you can send us your silver lamp ring and we will send it back in black coated.
Attention! With this article you order ONLY order the SERVICE that we powder coat your original parts. So you have to send us your parts and we will send them back after we powder coated them in black.
Duration until you have the part wiede is between 2 -3 weeks.
As standard, we always make the parts in black. Silk matt and many other colors are of course also possible on request.
Headlight R9T black coating
CB11703
/ RS0
€55.00*
True to the motto "black is beautiful" you can send us your original BMW R nine T lamp topg and we send it back to you in black coated.
Attention! With this article you order ONLY order the SERVICE that we powder coat your original parts. So you have to send us your parts and we will send them back after we powder coated them in black.
It will take 2 - 3 weeks until you have it back.
By default we always make the parts in black silk matt. Several other colours are also possible on request.
Reflector Cover - BMW
CB11931M
/ RS0
€67.95*
Covers for the original reflectors on the forks of all BMW R nine T & R12 models
As with all motorcycles since the Euro 4 standard, reflectors are also glued to the forks of the BMW models. It looks absolutely awful, but unfortunately it's mandatory. We have a chic solution here that covers the reflectors but can also be removed at any time.
Our high-quality aluminum covers give your motorcycle a classy and individual look. They not only enhance the look, but also integrate seamlessly into the design of your machine.
Easy installation: The covers are simply put over the existing reflectors and fixed with a grub screw on the underside. Installed in just a few seconds and removed just as quickly – with no effort at all.
Three stylish options to choose from:
Silver: Raw aluminum that you can either leave as is or polish to a shine. For the perfect finish, we recommend the Motul aluminum polish (see accessories).
Black: Completely black anodized aluminum for a subtle, elegant look.
Black with contrasting milling: Black anodized and subsequently milled for a special accent that attracts attention.
Scope of delivery: The covers are delivered as a pair.
Rizoma Alu Mudguard for all R9T models
CB11243M
/ RS0
€269.00*
Aluminum front fender suitable for R9T Classic models. As always with Rizoma the aluminum parts are a very high quality anodized brushed optics. This looks even more noble than simply plain aluminum.
The mudguard can be simply screwed to plug & play.
Rizoma rear underride R9T
CB11244
/ RS0
€157.50*
Passgenaue Rizoma rear lower shell (fits all R9T models).
As a result, the original taillight and flag carrier are removed.
For anyone who wants to build their own license plate, this signature offers the perfect foundation.
Oil filler cap Rizoma
CB11247M
/ RS0
€70.50*
Rizoma oil filler cap made of billet aluminum (highest quality & workmanship).
A key is required to be opened (included) so that the lid can not be stolen.
Rizoma hub cover CNC
CB11249M
/ RS0
€235.00*
The Rizoma hub cover replaces the original, quite simple plastic rings. Due to the milled aluminum rings the rim gets a much more chic look. Because just the rear wheel rim with the Einarmschwinge, is indeed an eyecatcher with the R9T. Due to the two different colors black or silver, a very nice contrast can be placed, which makes the caps particularly eye-catching.
The cover is only available in black as long as stocks last.
Rizoma Side Arm Kennzeichenhalter R9T
CB11223
/ RS0
€497.00*
The "Side Arm" kit is made up of an identification plate, which can be attached to the side arm. The "Side Arm" is a special styling for all demanding aesthetics, License plate light, reflector and a new rear under-fairing replacing the OEM component. The "Side Arm" kit eliminates the OEM tail light and turn signal. We recommend this with a taillight / turn signal combination (these connect taillight, turn signal & brake light in one), which makes for a fantastic look (appropriate holders are included in the kit, or you drill holes in the undercover). The turn signals are then mounted as in the photos to the left & right of the license plate). It is best to order it at the same time - you will be delighted! Optionally, we also offer you two optically cool rear wheel fenders. see accessories
Rizoma Side Arm / Outside BMW R9T
CB11226
/ RS0
€404.00*
The Rizoma license plate holder WITH undercover "Side Arm" is a particularly stylish eye-catcher for every demanding aesthete who would like to mount the license plate sideways to get a free rear end.The "Side Arm" kit consists of a license plate holder, license plate light and a new rear undercover, which replaces the OEM component. By mounting the "Side Arm" kit, the OEM tail light + turn signal is no longer necessary. We recommend this by a tail light/indicator combination (these combine tail light, indicator & brake light).
The holder is supplied with ABE. So it does not have to be registered.
Rizoma Licensholder Fox
CB11227.1M
/ RS0
€277.00*
The Rizoma label carrier "FOX" with or without taillight. is the absolute classic in the motorcycle industry for years and convinces without many words through its sophisticated adjustment system and perfectly developed construction. The rear of the BMW R nineT will be significantly shorter and sporty and tidier.
The scope of delivery includes: license plate plates, license plate light, bracket for Rizoma indicator, reflector, rear underfloor. The turn signal or turn signal / taillight combination can either be attached to the license plate with the included turn signal holders or two holes are drilled into the sub-trim. For the variant without taillight, a turn signal / taillight combination must be installed.
Alu parts Matt brush
CB11215M
/ RS0
€205.00*
We give the original R9T aluminum parts the right aluminum brushed cut look. Then the parts look like the brushed aluminum tank of BMW.
The parts are only chemically deteloxiert in our house, then polished by hand & brushed (therefore, the look is not always 1zu1 the same as the machined aluminum tank of BMW) and then still clear lacquer.
Then the parts have the surface which should have an aluminum part and not the silver anodal.
The whole takes about 2 weeks.
It is possible with the aluminum hump as well as with the air tunnel.
Fork covers R9T
CB11179.1M
/ RS1
€67.90*
A pair of Gaeblrohr covers made of lightweight aluminum in black powder coated or silver anodised.
Through the cover, the fork looks much more massive (because it seems wider), which makes the fork look significantly higher quality and ensures a lasting better look.
The tubes are supplied as a plug & play solution with rubber rings and installation instructions.
Fits on the Urban GS only when the indicators on the fork are turned off.
Original cream border black
CB10734
/ RS1
€80.00*
Colour:
Black
If the cast triangle does not look noble enough, the silver does not like, or it simply wants to have black (black is beautyful) we offer to the black with us powder.
Attention! With this article you order ONLY order the SERVICE that we powder coat your original parts. So you have to send us your parts and we will send them back after we powder coated them in black.Duration until their part is about 1 1/2 - 2 weeks. By default, we always make the parts in black satin or black glossy (please choose). Other colors are of course also possible on request.
The price is for the coating of both triangles.
Original frame triangle black powdercoated accents
CB11454
/ RS1
€125.00*
Colour:
Black
If the cast triangle does not look classy enough (because the original surface makes a pretty cheap impression), the silver does not like it, or it just wants to have black (black is beautiful) we offer it to us to have black powder. In this version, the original holes are reworked after the coating. This gives them a self-border, which makes the Rahmedreck look like a Fästeil optically.
Attention! With this article you order ONLY order the SERVICE that we powder coat your original parts. So you have to send us your parts and we will send them back after we powder coated them in black.
Duration until you recover the part is about 1 1/2 - 2 weeks.
By default, we always make the parts in black satin or black glossy (please choose). Other colors are of course also possible on request.
The price is for the coating of both triangles.
Short license plate holder - R12 nineT
CB12816
/ RS3
€149.95*
Short license plate holder for your BMW R12 Cruiser
You want to upgrade the rear of your BMW R12 and install small 3-1 LED turn signals? Our high-quality, short license plate holder made of aluminum makes it possible – and without much effort.
With this license plate holder, you can give your bike a clean look at the rear. The license plate holder comes with a high-quality LED license plate light (which is significantly smaller than the original). This is already equipped with the appropriate vehicle plug.With our short license plate holder, you have the option of removing the huge original indicators and mounting any small 3-1 accessory indicator with an M8 thread (note: if you want to mount Kellermann Atto indicators, you will also need the M5 to M8 adapters).You can order nice small 3-1 turn signals / rear light combinations with a 10% discount in the set below the description.
The original plastic holder looks pretty cheap in comparison, and the bulky, long license plate light plus the oversized reflector? A real style clash! With our elegant license plate holder, your license plate sits much better and blends harmoniously into the overall look of your motorcycle – for a clean and tidy look from behind.
Our Classicbike-Raisch license plate holder is made of sturdy aluminum in Germany and finished with a high-quality black powder coating. Everything is pre-assembled and wired by hand in-house, so you can be sure that the quality and appearance are right. That's why we also offer an extended 3-year warranty on the license plate holder.
Classicbike-Raisch tip:
If you want to be completely legal on the road, unfortunately you can't avoid a reflector. But don't worry, we offer you a slim, unobtrusive alternative to the chunky original. You can easily find it under “Accessories” in this product description.
For the perfect attachment of your license plate, we recommend that you order a set of license plate screws at the same time.
Headlight Plate Bates Style R9T
CB12008M
/ RS4
€94.95*
The aluminum headlight sheet metal clears the front of the R9T and prevents an open view of the steering head and all cables.Fits with the original headlight as well as with the small 5 3/4 headlight from our range.Fits the R9T Scrambler & Urban GS (for the GS the lamp mask has to be removed and the lamp holder of the scrambler has to be mounted).
To get a nice clean front, there is now the aluminum headlamp sheet metal in silver (aluminum raw optimal to use it simply to install it, polish it or brush it matt), black powder coated
The sheet metal is simply put between the two fork bridges, behind the headlight (headlight does not have to be disassembled) and then fastened to the two fork legs with leather straps (included in delivery, available in black or brown) (fits nicely so that nothing rattles). An assembly instruction is naturally also included.In addition, an edge tape is included in the scope of delivery, which looks nice and classic on the one hand and protects the cables and wires on the other hand.The assembly is quite simple and fast, the original headlight does not have to be disassembled.
Side licence plate holder - rear wheel BMW
CB12774
/ RS5
€239.95*
Side licence plate holder behind the rear wheel for BMW R nineT & R12 models.
This licence plate holder gives you the option of legally mounting your licence plate on the side without having to register the holder with the TÜV.A very practical solution for motorbikes that have a very short rear end and cannot find a good place to mount the licence plate and indicators or 3-1 indicator / tail light combination. In addition to the licence plate holder, you can also order indicator holders (see accessories below this description). With this solution, you can easily get your lights and licence plate into a legal position (no TÜV registration required).
The licence plate holder comes with a small LED licence plate light (road approval with E-number). This is fitted with a 120mm long carben.Dimensions of the licence plate: 176 x 127mm - this means that any licence plate can be fitted.
Alu rear fender - R9T
CB12368M
/ RS5
€449.95*
Rear wheel aluminum fender including holders suitable for R nineT.
The fender with the massive round tube holder underlines the classic line of the nineT series. In addition to the optics, the fender provides a very good splash protection as well as stone chip protection at the shock and in the rear area. Of course, a completely free rear wheel is visually cool, but it is absolutely impractical. When driving in the rain, you mess up the complete rear.
The fender comes with holder, mounting hardware and instructions.
Fender width: 160mm
Short Front Mudguard - R9T
CB11538.1M
/ RS6
€169.00*
A very short GFK front fender suitable for R9T Classic, Racer, Pure & Scrambler (with mounting material).Due to the short short design the mudguard gives the Motrrad a completely different look.The fender is made of high quality GFK and comes unpainted.
%
Carbon Cover Air Tunnel
CB10587
/ RS8
€228.99*
€241.00*
(4.98% saved)
Carbon cover air tunnel silver-black
Fork feets R9T black painting
CB11435M
/ RS9
€180.00*
Who does not like the original, silver fork feet on his R9T, they can simply be coated black with us. Simply send the disassembled fork to us and you get it back with black fork feet.
Who can not disassemble itself, which can also simply send the whole fork to us and we take over the work for you, in our chassis department. For this you choose the variant with assembly, then you just send us the dismantled fork, we disassemble it here on site and then reassemble it after coating. Directly with better oil, whereby the response of the fork is slightly improved.
Duration until you have the part back is about 2 - 4 weeks.
By default, we make the parts always in black satin. Several other colors are also possible on request.
The price is for the coating of both fork legs. Looks especially good in conjunction with black fork tubes.
Attention! With this article you order ONLY order the SERVICE that we powder coat your original parts. So you have to send us your parts and we will send them back after we powder coated them in black.
Duration until you have finished the part is about 2 - 3 weeks.
As standard, we always make the parts in black. Silk matt and many other colors are of course also possible on request.
The price is for the coating of both fork feet. Looks great in conjunction with black fork tubes.
R9T fork black anodize
CB11301M
/ RS9
€259.96*
Since many people don't like the gold fork on the R9T, we looked for a way to get it reasonably black without having to buy a complete Öhlins fork. We offer a very high-quality black anodising for the fork tubes, which give the bike a completely different look.
For this, the dismantled, disassembled & cleaned fork tubes have to be sent to us. Or you can choose the assembly option, in which case you simply send us the dismantled fork, we disassemble it here on site and then reassemble it after anodising. Directly with better oil, which improves the response of the fork.
Anodising & shipping takes between 6 - 10 weeks. If that takes too long, you can opt for new stanchions, which we have in stock (see similar items in this description).
Attention: blackening of the fork legs is not included (extra items see accessories).
Dakar front mudguard - R9T
CB12887
/ RS10
€195.00*
Top-mounted high front mudguard in Enduro Dakar style for all BMW R nineT models in matt black
This mudguard in Dakar style from MOTOISM gives your R nineT a new look. The slightly angular top mudguard looks particularly good on Enduro / Scrambler conversions. But the mudguard also looks great on a Pure or Classic. The angular rather than round shape is reminiscent of Enduro / Super Moto machines. This makes your R nineT stand out from the crowd.
Classicbike-Raisch style tip:
The mudguard looks particularly cool in combination with the MOTOISM lamp mask kit.Both products together round off the handle and make your R nineT a real eye-catcher.You can find the lamp mask under the accessory products in this description.
Material & finish:
As with almost all MOTOISM parts, the mudguard is manufactured from the highest quality materials using a state-of-the-art 3D printing process.After printing, the mudguard is primed and painted matt black
Scope of delivery:
Mudguard in matt black
Mounting material
Stainless steel bracket
AC Schnitzer front spoiler - R nineT
CB10710
/ RS10
€499.00*
AC Schnitzer front spoiler / belly pan for BMW R nineT & BMW R12 nineT
Cafer-Racer GRP front spoiler which gives the motorcycle a new look, as befits a classic CafeRacer conversion.The front spoiler gives the R9T a really sporty look! Fits particularly well with sporty conversions and classic retro racers. The design of the front spoiler goes particularly well with the half shell of the R9T Racer.
Installation of the front spoiler is simple. All necessary mounting materials and installation instructions are included.
The spoiler is supplied unpainted with a primer. Perfect as a basis for you to have the front spoiler painted by your trusted painter.
Including installation instructions and part certificate.BMW R nineT front spoiler by AC Schnitzer made in Germany
Perfect fit & workmanship
Easy assembly thanks to assembly instructions
Cafe Racer look
Part certificate
Cooler grid
CB12273
/ RS10
€100.00*
Aluminum lasered protective grille for the oil cooler of all BMW R nineT models from the brand Unit Garage from Italy.
The protective grille serves two purposes.First and foremost, it protects the radiator from rough stone chips, which is especially important if you are also a bit off road.In addition, the grid also looks visually nicer than honeycomb structure of the original oil cooler.
The grid is made of aluminum and anodized black.
License support sideways - AC Schnitzer
CB10597
/ RS18
€279.00*
AC Schnitzer license plate holder, for side mounting of the license plate with TÜV parts certificate.
Manufactured from high quality aluminium, black anodized and with accent milling to give the surface an even higher quality finish.As usual, top quality from AC Schnitzer.The scope of delivery includes an LED license plate light, as well as all the necessary installation materials and installation instructions.
Perfect for anyone who wants to fit a clean rear without a license plate or a short aluminium mudguard.
The practical thing about this license plate holder is that it does NOT have a license plate plate. This means that it can be used optimally for any license plate size.
With parts certificate means that the license plate holder is supplied with TÜV papers and can be easily (and cheaply) registered.
License plate size:The mount for the license plate has a dimension of 150mm height - 110mm width. In other words, all license plates that have at least this dimension can be optimally installed and cover the holder.Suitable for all countries.
Rear conversion AC Schnitzer
CB10600
/ RS21
€159.00*
AC Schnitzer rear rear fenders with new LED taillight (no backlight) with ABE
Footrests R9T black Powder coating
CB12321
/ RS52
€60.00*
You like the original rests of your machine, but you do not like them in silver?
Then just send them to us and we will coat it black satin (RAL9005) powder.
The price is for ONE PAIR of pegs. Please remove all attachments like rubbers or similar from the footrests and do NOT send them to us! Please note that the coating in the area where the foot rests will wear off over time.
The processing time is approximately 3-4 weeks.
Attention! we offer here only the service of the coating. The original part must be delivered to us by the customer.
Lamp mask set - BMW R9T
CB12884
/ RS100
€329.00*
Koso Thunderbolt headlight mask kit "Controlpit Tree" for BMW R nineT by MOTOISM
Turn the front section of your R nineT into an eye-catcher with the headlight / lamp mask combination of KOSO Thunderbolt LED headlight & MOTOISM lamp mask. This plug & play kit is supplied with all the necessary installation materials and resistors for your BMW. Like all parts, the lamp mask is manufactured to a very high standard by our friends at MOTOISM and painted matt black.
Scope of delivery:
- Lamp holder: The lamp holder is screwed plug & play to the triple clamps of your R9T. The Koso headlight and the Controlpit Tree lamp mask are mounted on this.- Lamp mask: The matching lamp mask in matt black is included in the scope of delivery.- LED headlight: The Koso Thunderbolt LED headlight is included as an option (please select variant).- Resistors : Depending on the motorbike model, the necessary resistors are included in the scope of delivery, which are required so that the Thunderbolt headlight can be installed and no error message appears in the speedometer.
Accessories recommendation:
To avoid having to cut off the original glass base adapter for the parking light during installation, we recommend ordering the parking light adapter from our range (see accessories in this description). Optional mount for Motogadget Mini speedometer: On request, the headlight mask can be supplied with a mount for the Motogadget Mini speedometer (also visible on some product images here). If you are interested, please contact us.
Classicbike-Raisch style tip:
To round off the style of the mask and get a really cool front end look, we recommend ordering the Dakar front mudguard (this is also fitted in the product photos).You can find the mudguard under the accessories in this description.
Roadstar tail tidy BMW R nineT
CB12827
/ RS100
€659.00*
Short Unit Garage 1-piece rear fender for your BMW R nineT Roadster
The shortest rear end for true individualists
Are you looking for one of the most compact and stylish rear ends for your BMW R nineT Roadster? With the Unit Garage 1-piece rear fender, you can take your bike to a new level! This rear fender is one of the shortest currently available on the aftermarket for the nineT Roadster – perfect for a clean, minimalist look.
Optimized for the R nineT Roadster and Classic models
On the Roadster and Classic models of the BMW R nineT, the pillion frame and the entire rear frame can be removed and replaced with screws. This makes it super easy for you to convert to a sleek 1-man rear end. But let's be honest: if you just remove the rear frame and the pillion pad, the rear often looks unfinished. This is where the Roadster rear end from Unit Garage comes in.
With this rear end, you not only get the option of removing the pillion section, but also a clean and stylish finish – so your bike looks great all round!
Complete kit with everything you need
The kit includes everything you need for the conversion:
Detailed assembly instructions
All the necessary mounting materials
The conversion is quick and easy, so you can get started right away!
Lighting: modern LED technology
The kit includes an LED stripe rear light that combines a rear light, brake light and turn signal in one. Particularly cool: the turn signals light up at the ends of the stripe (watch the video in the product description).
Note: The rear light does not have an E-number/approval. However, in our experience, there are no problems with authorities because the rear light and turn signals are very visible.
Compatible with side license plate holders
The 1-man rear fender is compatible with all side license plate holders in our range. You can find these directly below the product description in the accessories.
Paintwork
The rear kit is available directly from the manufacturer Unit Garage in a range of colors (these are all compatible with the Unit Garage tanks that we also have in our range).The kit is also available in RAW/unpainted, so that you can then have the rear painted in your favorite motorcycle color.
Tail light replacement - R12 nineT
CB12883
/ RS600
€44.95*
Tail light replacement cap for BMW R12 nineT
This cap gives you the option of removing the original rear light on your nineT and converting it to a 3-in-1 indicator / rear light combination.
With the R12 ninet, you can no longer easily remove the rear light, as this is integrated into the seat / hump.However, if you would like to convert your nineT to modern 3-in-1 indicators (with integrated brake/rear light), you can order the rear light replacement cap and fit it instead of the original rear light.
Classicbike-Raisch conversion tips / accessories: With original mudguard:- 3 in 1 indicators (you can find a selection in our shop under lighting) - Indicator adapter (necessary for mounting the accessory indicators) - see accessory article in this description - Short licence plate holder - see accessories in this description Clean, tidy rear:- If you want a really clean rear without the original mudguard, we recommend our Rear Eliminator Kit - see accessories in this product description.
Fork stanchions black DLC coating
CB12835
/ RS600
€399.00*
DLC coating in black for fork tubes.
Do you want a black fork? Are you not satisfied with the black outer tubes and fork feet? No problem, we can also DLC coat the inner fork tubes for you.
Either you send us your removed tubes and we will send them back to you coated, or you send us your complete fork, we will disassemble it and then send it back to you newly coated and reassembled. But please contact us beforehand so that we can make you an offer for the labour costs.
Classicbike-Raisch tip:If you would like it all black: we also offer other coatings for the original fork (such as powder coating the fork feet black / anodising the outer fork tubes black).
The duration for the coating is approx. 2 - 4 weeks. The price is for a PAIR.
Unit Garage valve covers R9T
CB12640.1M
/ RS600
€1,039.95*
Black aluminum valve covers for our BMW R nineT Boxer engines from Unit Garage.
These covers are die-cast in a specially produced mold and then painted black to perfectly match the engine of your R nineT. The attached covers (which are available in either black or silver) are CNC-milled from aluminum.
The Unit Garage valve covers are a beautiful blend of classic / perforated covers paired with a modern, CNC machined accent.
Rear mudguard - R9T
CB12577M
/ RS600
€519.95*
GRP rear fender conversion kit including license plate holder, tail light & license plate light (with E-number).
Many people want a classic rear mudguard on their nineT. Here is the solution from Unit Garage. A very high quality GRP mudguard that fits with the original seat as well as with all accessory seats from our range. The scope of delivery includes both license plate and blinker holder. Both can, but do not have to be fitted, so this mudguard can also be used with a side license plate holder.
There is a suitable plug on the rear light so that the kit can be connected plug & play to the original wiring harness.
The white of the cap is the same color (light white) as the Urban GS.
Air Intake Cover - Titanium
CB12478.1M
/ RS600
€265.00*
A pair of titanium covers for the rubber intake hose of all BMW R nineT models.
The covers are quick and easy to fit. They are simply pushed over the intake rubber and then hold in place.
In the titanium version, with visible welds, an absolute eye-catcher!
Handmade in Italy.
Grid intake manifold
CB12369
/ RS600
€169.95*
Aluminum grille + ring for the intake manifold of all BMW R nineT models.
The Gitte provides a more beautiful / harmonious finish of the original air intake manifold on the nineT models.
No drilling or similar is necessary for mounting.
Rizoma frame triangles
CB12305
/ RS600
€749.00*
3D milled Rizoma valve cover cover for BMW R nineT.
This in Italy in the house Rizoma manufactured valve cover, are milled in 3D driving from a large aluminum part. Also, of course, the triangles have the unique, from Rizoma known surface with fine, extra visible milling structure.
In the aftermath, the covers are anodized deep black and then milled again in spots to achieve the elegant black / silver look.
Who wants to build a really classy R nineT and attaches great importance to detail, we recommend the complete Rizoma milled parts line to install on his machine. All other parts from the line can be found under the similar products in this description.
Intake manifold cover
CB12274
/ RS600
€209.95*
A pair of stainless steel covers for the rubber intake hose of all BMW R nineT & R12 models.
The covers are very easy and quick to fit. They are simply pushed over the rubber intake hose and are held in place.Visually, of course, only a small detail, but these covers make a big difference! The original rubber hoses don't really do anything visually here. The high-quality stainless steel covers give the BMW's intake area a much more valuable look.
Activated Carbon Filter Removel Kit
CB12264
/ RS600
€19.95*
Many are the large activated carbon filter in the R nineT Euro 4 models a thorn in the eye. To us it was also with our latest Scrambler conversion.
So we have put together a small and simple kit to remove the filter. The kit includes all materials and step by step instructions to remove the filter cartridge without further work.
Cover caps set BMW R9T frame
CB12062M
/ RS600
€47.95*
CNC FRAME CAP Set, 2-piece or 7-piece suitable for all BMW R nineT models.
ATTENTION: From model year 2016, the frame has been changed on some models. As a result, the cover cap (vehicle side viewed from the left) top right (above the cylinder head- injector) does not fit! (SEE PHOTO)
The black anodized aluminum caps cover the frame holes of the BMW RnineT. Combined with polished bevels, these caps stand for a classy, stylish design.
Scope of delivery: 1 set, 2-piece1x swingarm closure cap, left1x swingarm closure cap, right
Scope of delivery: 1 set, 7-piece1x swing arm cover, left1x swing arm closing lid, right1x Upper swing arm cover, right2x Lower motor cover, right / left1x Upper motor cover, front1x Upper motor cover, rear
Start license plate for SLC holder
CB12049M
/ RS600
€55.00*
SW-Motech start number plate suitable for all Sw-Motech Legend Gear SLC bag holders (matching holders see ZUbehörartikel in this description).
The plate is made of brushed aluminum and looks very high quality. On request, we can also coat this black powder for an additional charge.
The sign is very easy, just like the Legend Gear bags with the quick release system clicked into SLC holder.
Perfectly suited for all who have installed the SLC holder and do not always want to have the bag on the bike but do not want to look at the holder.
Break lever black coating
CB12319
/ RS600
€45.00*
Black is beautiful! True to this motto, we offer you the possibility of virtually all metal attachments of your machine to send to us and we powder coat them to you in black satin and send them back to you.
Simply send us the dismantled brake lever and we will take care of everything else.
Delivery time is about 2-3 weeks.
Attention! We offer here only the service of coating. The original part must be delivered to us by the customer.
Coat lamp holder black
CB12378
/ RS600
€15.00*
Who can coat his triple clamps black, which should also coat the lamp holder of his R nineT, because this part is directly on the lower triple clamp.
Duration until you have the part back is about 2 - 4 weeks.
Steering damper bracket black coating
CB12379
/ RS600
€25.00*
Also the small steering damper holder of your nineT we can coat you black. This we can especially recommend if you have your triple clamps coated black, because the holder is screwed directly to the bridge.
Duration until you have the part back is about 2 - 4 weeks.
Body parts and rear end conversions for your BMW Heritage Line motorcycle: style and function
Customise your BMW Heritage Line motorcycle, such as the R nineT, R9T, R12, R12 nineT, R nineT Scrambler or R nineT Pure, entirely according to your wishes with high-quality body parts! Discover everything you need for an individual look and optimised function: from stylish emblems to versatile rear conversion kits and central or side licence plate holders. Robust mudguards and precisely fitting side covers provide a distinctive design and improved protection. Our body parts have been specially developed for the BMW Heritage models so that you can refine your machine both visually and technically. Make your bike unique and make an appearance that inspires – quality and style perfectly combined!