Skip to main content Skip to search Skip to main navigation

Zard Speed Twin / Thruxton 1200 GP Exhaust

Product information "Zard Speed Twin / Thruxton 1200 GP Exhaust"

Zard 2-2 Slip On Stainless Steel Exhaust

for Triumph Speed Twin & Thruxton 1200

ATTENTION
For Thruxton 1200 & Speed Twin Euro 5 models from 2021 WITHOUT ABE.


Suitable for:

  • Triumph Speed Twin 1200

  • Triumph Thruxton 1200

The exhaust system is with E-number.
Racing version (without E-number and cheaper) available on request.


Design & look

Very high-quality stainless steel silencers - really short and crisp.
Visually, they are somewhat reminiscent of a Moto GP exhaust.

The short design perfectly emphasises the sporty lines of Speed Twin & Thruxton.
The chunky original exhaust, on the other hand, is always a bit distracting.

If the whole thing is too small and too sporty for you, the Zard Conical is the better choice.


Sound

The sound is audibly throatier and more present, but to our ears it falls short of the really big AHA effect.
Sound video see below.

If you want a throatier and louder sound, you should also order the additional Zard Racing DB killers (see accessories - without road approval).

With the racing DB killers, the 1200cc engine gets the throaty, muffled bass sound you want.
Advantage: A DB-Killer remains installed, the bike is not excessively loud and everything looks original.

To remove the original DB-Killer, a hard-to-reach welding point has to be drilled out and milled away (a little more than half an hour's work).
If you want to have this done by us, order the additional item "DB-Killer removal Zard exhaust CB11514" (see accessories).

If that's not enough, fit the X-pipe (cat replacement pipe) - see accessories.


Black version

The exhaust is not directly available from Zard in black.
At the customer's request, we have the system coated in black in Germany - very high quality, resistant and deep black.


Swiss customer / authorisation

For Swiss customers, the exhausts can be supplied with a declaration of suitability.

Triumph LC models from 2016:
  • Speed Twin - 1200
  • Thruxton 1200
  • Thruxton 1200 R
  • Thruxton 1200 RS
Triumph LC ab 2016
Speed Twin 1200 EU 4
Speed Twin 1200 EU 5
Thruxton 1200
Thruxton 1200 R
Thruxton 1200 RS / FE
0
0
0
0
Skip product gallery

Accessories

ESD ceramic coating CB11371M / RS0
Ceramic coating, heat-resistant in black. Only the rear silencer(s). Heat protection plates, brackets or similar are charged separately (if available).

From €190.00*
Zard racing DB-Killer CB11523 / RS1
Raisch racing DB Killer for Zard short exhaust systems. More sound + more performance through more throughput. Approx. 40% larger hole. With our DB Killer there are now 3 sound variants available for the Zard systems. With original DB Killer, with Raisch DB Killer or without. Our DB killers are without ABE. They are supplied in pairs.To be honest, with the original DB-killers you only get a very small sound compared to the standard version. Since most of them do not want to drive without DB-killers, we have made this more open variant. It looks like you have a legal DB-killer in it, but it sounds really good! With these db-killers the Zard systems get the sound they need.

€64.90*
X-Pipe / KAT & Front silencer replacement CB11302 / RS0
These X-Pipes replace the original Cat-Box / front silencer, which provides a much more pithy sound. In combination with an additional open exhaust system you get a really pithy, dull but also loud sound. That's exactly how a 2 cylinder must sound!In addition, there is a weight saving of 1.7 kg compared to the standard catbox. If the X-Pipe is not only about the more beautiful and louder sound, but also about noticeably more power, we advise you to use one of our power kits, in which the X-Pipe is included. Then the whole thing brings also a strongly noticeable performance gain. Click here for our performance kits. The original veneer can be used again, so that the X-Pipe is not optically noticeable.  Do NOT fit to Thruxton TFC!

€209.95*
DB-Killer Zard 400er extension CB11514 / RS0
To use the DB-Killer on the Zard exhaust system, a fine welding spot has to be drilled out and milled away. Afterwards the exhaust has to be reworked at the guide for the Segering.If you don't want to do this work yourself, you can order it here, then the exhaust will be delivered with easily removable DB-killers (by snap ring).

€65.00*